Connectivity issue with RUCKUS

[Jyothik16]

I have been using RUCKUS for more than three years and never had a any issues. Past from few days I challenges to access Internet through RUCKUS

appreciate if you could help me to resolve this.

Jyothi

[Imran_ruckus · Accepted solution]

Hi @Jyothik16 

Thank you for the response and the detailed information you shared. 

This issue is because your switch is running on the Routing code (SPR). The Switch should run on the Switching code (SPS) to avoid these issues for Lennar home users. Due to a power outage/power spike, the Switch boots up on the other partition which may be running on a ‘Routing Code’ results in causing this issue.

As I can see from the output you shared, your Switch is booted up on the secondary partition which is running on Routing code (SPR) as highlighted in the below screenshot. 

Please Enter the below commands in CLI to fix this issue:

Note: Hit Enter to accept each command 

enable

copy flash flash secondary 

boot system flash secondary yes 

Example: 

VIDEO LINK AS REFERENCE: https://www.youtube.com/watch?v=Eem1IBgYaWc

ICX7150-24P Router>enable (hit enter to accept the command) 
ICX7150-24P Router#copy flash flash secondary (hit enter to accept the command and wait: until the flash finished) 
ICX7150-24P Router#boot system flash secondary yes (hit enter to accept the command: the switch will reboot)

We suggest upgrading your switch to the latest stable version to avoid this issue in the future. Your Switch is on an older version that is 08080d. Please let us know once you complete the above process to assist you with the Upgrade of the Switch.

Please let me know if you have any queries in this regard.

NOTE: Please feel free to mark the post as ACCEPTED SOLUTIONS.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Jyothik16]

DownstairsUpstairs

[Jyothik16]

Yes, internet is working using local provider router

[Imran_ruckus]

Hi @Jyothik16 

Thank you for the response and the detailed information you shared.

As per the pictures you shared, light status of the Switch and the Access Point seems to be normal.

This issue may happen when the Switch runs on the Routing code (SPR). The Switch should run on the Switching code (SPS) to avoid these issues for Lennar home users. If the Switch boots up on the other partition (Due to a power outage/power spike) which may be running on a ‘Routing Code’ results in causing this issue. To check the same please follow the below process.

Please follow the below steps and help us with the queries,

1. To check this issue, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily. 

How to find my Ruckus “Devices IP address” using free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Device...

2. Once we identify the IP address of the switch proceed to access remotely to the device “Command Line” 

How to remotely access to 'ICX 7150-C12P' or 'access points' "Network devices":

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-IC...

If you can access the Command line should look like this:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

Please enter the below commands once you log in to CLI and share the output.

Note: Hit Enter to accept each command 

enable 

show version

show flash

Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Jyothik16]

Hello,

I could locate IP address and opened putty. But it does not give me any command line to execute rest of the command lines as described in the follow pages

[Imran_ruckus]

Hi @Jyothik16 

Thank you for the response and the update.

May I please know what is the error you are getting on Putty when you are trying to access the Switch CLI? Please share the screenshot of the same.

Thank you again for your patience.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.