cancel
Showing results for 
Search instead for 
Did you mean: 

Firmware Upgrade for ICX7150-C12 Switch - Need help locating Firmware version and help upgrading

MiSNemesis
New Contributor

I have a ICX 7150 since 2020 and was never upgraded.  I am at a lost as to how to locate the version and then what upgrade is necessary to use.  Any help would be appreciated.

1 ACCEPTED SOLUTION

Jayavidhya
Moderator
Moderator

Hi @MiSNemesis 

 

The recommended firmware version for ICX 7150 Switch is SPS08095dufi.bin 

 

Please follow the below guides to perform an upgrade to the code 08095g UFI and upgrade both partitions with the switching code file named SPS08095gufi.bin to avoid the issues in future.

 

1.Upgrade a Switch ICX-7150-C12P using a USB flash drive

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

 

2. Upgrade a Switch ICX7150-C12P via TFTP

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

 

3. Upgrade a switch via Web GUI (ICX7150 Switch)

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-an-Upgrade-vi...

 

 

Please let us know if you have any queries in this regard.

 

Best regards,

Jayavidhya

Lennar Home Community

View solution in original post

36 REPLIES 36

SSH@ICX7150-C12 Switch#show version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Apr 11 2023 at 00:06:30 labeled as SPS08095j
(31457280 bytes) from Primary SPS08095j.bin (UFI)
SW: Version 08.0.95jT211
Compressed Primary Boot Code size = 786944, Version:10.1.26T225 (mnz10126)
Compiled on Tue Nov 29 08:43:26 2022

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X10GR POE 12-port Management Module
Serial #:FEK3203P15K
Software Package: BASE_SOFT_PACKAGE
Current License: 2X10GR
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8 MB boot flash memory
2 GB code flash memory
1 GB DRAM

----------------------------------------------------

SSH@ICX7150-C12 Switch#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 31457280, Version:08.0.95jT211 (SPS08095j.bin)
Compressed Sec Code size = 31457280, Version:08.0.95jT211 (SPS08095j.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.26T225 (mnz10126)
Compressed Sec Boot Code size = 786944, Version:10.1.26T225 (mnz10126)
Code Flash Free Space = 1110274048

 

----------------------------------------------

 

SSH@ICX7150-C12 Switch#show inline power

Power Capacity: Total is 124000 mWatts. Current Free is 124000 mWatts.

Power Allocations: Requests Honored 0 times


Port Admin Oper ---Power(mWatts)--- PD Type PD Class Pri Fault/
State State Consumed Allocated Error
-----------------------------------------------------------------------------
1/1/1 On Off 0 0 n/a n/a 0 n/a
1/1/2 On Off 0 0 n/a n/a 0 n/a
1/1/3 On Off 0 0 n/a n/a 0 n/a
1/1/4 On Off 0 0 n/a n/a 0 n/a
1/1/5 On Off 0 0 n/a n/a 0 n/a
1/1/6 On Off 0 0 n/a n/a 0 n/a
1/1/7 On Off 0 0 n/a n/a 0 n/a
1/1/8 On Off 0 0 n/a n/a 0 n/a
1/1/9 On Off 0 0 n/a n/a 0 n/a
1/1/10 On Off 0 0 n/a n/a 0 n/a
1/1/11 On Off 0 0 n/a n/a 0 n/a
1/1/12 On Off 0 0 n/a n/a 0 n/a
-----------------------------------------------------------------------------
Total 0 0
--More--, next page: Space, next line: Return key, quit: Control-c

 

--------------------------------------

SSH@ICX7150-C12 Switch#show inline power detail


Power Supply Data On unit 1:
++++++++++++++++++

 

Power Supply Data:
++++++++++++++++++

Power Supply #1:
Max Curr: 2.3 Amps
Voltage: 54.0 Volts
Capacity: 124 Watts
PoePower: 124 Watts


POE Details Info. On Unit 1 :


General PoE Data:
+++++++++++++++++

--More--, next page: Space, next line: Return key, quit: Control-c

 

Hi @MiSNemesis 

Thank you for the response and the information you shared.

The output of the commands seems normal. 

Could you please let me know if your Access Points have any of the lights ON?

Please check and let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

 

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

No lights at all.  when I look at the Switch, there is no connection going on with the network cables.  I rebooted the switched and remove and plug the cables back in.  Still no lights.

Hi @MiSNemesis 

Thank you for the response and the information.

Could you please plug the APs ethernet cable on other ports (any within 12 ports as shown in the below screenshot) and try check the AP again?

Please check and let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

 

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

20230710_203405773_iOS.jpgI removed and move to another empty port.  Still no lights.