R510 no power, PoE fatal error, switch username and password not working, PWR and SYST are green

[Jayavidhya · Accepted solution]

Hi @needhelp 

Based on the troubleshooting done, seems that the PoE port is not  responding  this unit should be RMA (return merchandise authorization) in simple words replace it.

Feel free to contact us via chat, comment you already have a post, copy the link from the post (URL) and paste it into the chat to start unit replacement.

The below link is to contact us by chat (only)

https://support.ruckuswireless.com/contact-us

Please let us know if you have any queries in this regard.

Best regards,

Jayavidhya

Lennar Home Community

[Imran_ruckus · Accepted solution]

Hi @needhelp 

Greetings!!!

Thank you for the response and the information you shared.

Please note, both Access Points need to be upgraded to the same version in order to get them connected on a single Unleashed system.

If you are unable to perform the Unleashed Upgrade online, please perform an offline/local upgrade.

And you can Upgrade to version 200.14.6.1.199 which is recently released.

Please refer to the below video showing the process of Local Upgrade.

https://www.youtube.com/watch?v=vCqiH2Aoxlk&t=66s

Please let us know if you have any queries in this regard.

Thank you again.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Jayavidhya · Accepted solution]

Hi @needhelp 

It seems like your ICX7150 is running 8090j code. The recommended firmware version for ICX 7150 Switch is SPS08095dufi.bin .

Please perform an upgrade to the code 08095g UFI and upgrade both partitions with the switching code file named SPS08095gufi.bin, 

1.Upgrade a Switch ICX-7150-C12P using a USB flash drive

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

2. Upgrade a Switch ICX7150-C12P via TFTP

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

3. Upgrade a switch via Web GUI (ICX7150 Switch)

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-an-Upgrade-vi...

Please let us know if you have any queries in this regard.

Best regards,

Jayavidhya

Lennar Home Community

[Imran_ruckus · Accepted solution]

Hi @needhelp 

Please perform the below commands.

enable 

configure terminal

ip address 10.106.0.10 255.255.0.0

ip default-gateway 10.106.0.1

write memory

exit

After performing the above commands, please share the output of the below command.

enable 

show ip address

ping <ip address of the master AP> (Please use IP address of the Master AP here)

Please check and let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Imran_ruckus · Accepted solution]

Hi @needhelp 

Thank you for the response and the information you shared.

The ‘show who’ command output seems to be normal.

Please remove both the Switches from the Unleashed. 

Once removed, reboot the Switch once by performing the below commands.

enable 

reload

y

And also, please reboot the Access Points as shown in the below screenshot.

Once the Access Points, Switch reboots and comes online please check the Switch status on the unleashed. 

Please share the screenshot of the same.

Please check and let me know if you have any queries in this regard.

Thank you again. We appreciate your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Imran_ruckus · Accepted solution]

Hi @needhelp 

Thank you for the response and the information.

Yes, there will be only One Switch that will appear in the Unleashed that is trying to get in sync with the Unleashed system. Since we were trying to add manually maybe there were 2 Switches got listed previously (One trying on its own and the other one we tried to add manually).

At this point, we should factory reset the RUCKUS ICX-7150-C12P Switch as it is not getting in sync with Unleashed with the other troubleshooting steps we tried.

Please note, there will NOT be any loss of data or configuration. Factory reset will just reset with the default configuration. 

Please perform the below commands to factory reset the RUCKUS ICX-7150-C12P Switch. (Also please refer to the below screenshot)

enable 

erase system factory-default

y

Once the factory reset is complete, the RUCKUS ICX-7150-C12P Switch will discover the Access Points connected to it and it gets connected to the Unlashed system.

Please make sure the management approval is enabled (as described in the below link).

https://docs.commscope.com/bundle/unleashed-200.9-onlinehelp/page/GUID-A887C55E-6973-4496-9413-302E8...

Please check and let me know if you have any queries in this regard.

Thank you again. We appreciate your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Imran_ruckus]

Hi  @needhelp 

Thank you for the response and the information.

Could you please check the ethernet cables of the APs or check replacing them with other working ethernet cables? In case if connected ethernet cables of APs are damaged.

Also, please try to factory reset the APs as you performed before, if there is a red light when you press the reset button on the AP with a stick or paper clip.

Please let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[needhelp]

I removed both APs and plugged them each into a shorter cable connection to the switch. Both powered on. I used a basic cable tester, and on both home installed cables, the main unit showed a good connection, but the remote tester for the second AP cable (furthest from the switch) scan showed it skipped lights on 1 and 2, but lights 3 through 8 came on, and the remote tester for the master AP cable (closest to the switch) scan showed it skipped lights 1 but lights 2 through 8 came on. Is it normal for a cable tester to have the main unit show a good connection but the remote say otherwise? I swapped the tester's main unit and the remote on both home installed cables, and the results were the same. I will contact Lennar to fix the cable issue.

The master AP has two IP addresses, one on 10 and another on 192, and is connected to the internet, but the switch shows disconnected on IP address 10.106.0.10. The second AP is on but not connected to the unleashed dashboard.

[Imran_ruckus]

Hi @needhelp 

Greetings!!!

Thank you for the response and the detailed information.

From all the 12 PoE ports of the Switch, the Access Points should receive power with a working ethernet cable.

Could you please share a screenshot showing the Access Points list from your RUCKUS Unleashed system? (Please refer to the below screenshot)

Please let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[needhelp]

Both APs are getting power. The unleashed dashboard shows the master AP is connected but not the second AP. The internet and the switch are connected. I did a reset on the second AP, and it does not allow me to sign on to it. This is weird because the advanced IP scanner shows the second AP is connected, but the last digit of the MAC address is a digit higher.

[Imran_ruckus · Accepted solution]

Hi @needhelp

Thank you for your patience.

As we checked in the private chat/posts.

Based on the troubleshooting done, and you confirm after performing the reset of the Access Point, checking all the connectivity and connections, the failure persists. This Access Point Unit Should be RMA (Return Merchandise Authorization) in simple words replacing it.

Feel free to contact us via chat, comment you already have a post, copy the link from the post (URL) and paste it into the chat to start the unit replacement.

Please follow the below steps as shown in the below example:

As shown in the below picture, copy the link and share it via chat from the link provided below:

The below link is to contact us by chat (only)

https://support.ruckuswireless.com/contact-us

NOTE: Please feel free to mark the post as ACCEPTED SOLUTIONS.

Please let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.