Lennar ICX7150-C12 Switch unable to reset after power outage.

[Rayoub]

Hi, I am unable to reset ICX7150-C12 after power outage... Lights flash amber continuously and no power goes to Access Points in home. I am unable to console connect to switch using a MAC. Requesting help here. Thank you

[Rayoub]

thank you Imran after about 15 reset I have these status lights. Please I would like to help to prevent this from happening again. I only have access to MacBook. 

[Imran_ruckus]

Hi @Rayoub 

Greetings!!!

Thank you for the response and the update.

Great!!! Good to know that Switch is back to its normal state.

To avoid this issue in the future, we must Upgrade your RUCKUS ICX-7150-C12P Switch to the latest stable version.

We must check your current version of the Switch to proceed further. Please follow the below process and help us with the command outputs to check the same.

And I would suggest, and request arrange a Windows laptop/PC for the upgrade process. Since it is much easier.

Please follow the below steps and help us with the queries,

1. To check this issue, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily. 

How to find my Ruckus “Devices IP address” using free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Device...

2. Once we identify the IP address of the switch proceed to access remotely to the device “Command Line” 

How to remotely access to 'ICX 7150-C12P' or 'access points' "Network devices":

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-IC...

If you can access the Command line should look like this:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

Please enter the below commands once you log in to CLI and share the output.

Note: Hit Enter to accept each command 

enable 

show version

show flash

Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again. We appreciate your patience and understanding. 

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Rayoub]

Hi Imran I was finally able to connect to the IP address of the switch and get version information. here it is.

Running Image Version:

SW: Version 08.0.90dT213
Compiled on Sep 23 2019 at 00:00:25 labeled as SPR08090d

[Imran_ruckus]

Hi @Rayoub 

Greetings!!!

Thank you for the response and the information you shared. 

This issue is because your switch is running on the Routing code (SPR). The Switch should run on the Switching code (SPS) to avoid these issues for Lennar home users. Due to a power outage/power spike, the Switch boots up on the other partition which may be running on a ‘Routing Code’ results in causing this issue.

As I can see from the output you shared, your Switch is booted up on the secondary partition which is running on Routing code (SPR) as highlighted in the below screenshot. 

Please Enter the below commands in CLI to fix this issue:

Note: Hit Enter to accept each command 

enable

copy flash flash secondary 

boot system flash secondary yes 

Example: 

VIDEO LINK AS REFERENCE: https://www.youtube.com/watch?v=Eem1IBgYaWc

ICX7150-24P Router>enable (hit enter to accept the command) 
ICX7150-24P Router#copy flash flash secondary (hit enter to accept the command and wait: until the flash finished) 
ICX7150-24P Router#boot system flash secondary yes (hit enter to accept the command: the switch will reboot)

Please let me know if you have any queries in this regard.

NOTE: Please feel free to mark the post as ACCEPTED SOLUTIONS.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Rayoub]

Is there any way to do this through the web portal? Thank you!