Lennar ICX 7150-12P Very slow - current forum instructions not working

[ahalper0227]

Help!  My Lennar-installed Ruckus system is very slow compared (150-200 mbps) to the internet to the AT&T gateway (~1000 mbps).  I am trying to follow the instructions in the following posts:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-solve-the-routing-cod...

In my terminal I cannot get the functions to work that the instructions call for.  Every time I try to use "show version" or "show flash" or “boot system flash primary yes” or "copy flash flash primary" or "copy flash flash secondary" the terminal says "The command is either unrecognized or incomplete. To view a list of commands that you can run  from this context, type '?' or 'help'."  

I am using a Mac for troubleshooting - PC not an option.

Please help asap!

[ahalper0227]

I am able to access the switch IP.  I have tried these instructions with no luck on the speed. 

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

My router from ATT is showing near 1000 mbps, but still the slow speed once I switch to the Ruckus system.  I confirm that everything is in the proper sequence and I am booting from SPS.  It seems that the switch has another issue that is significantly slowing down the wifi. 

Running Image Version:Flash Primary Image Version:Flash Secondary Image Version:

SW: Version 08.0.90dT211 Compiled on Sep 22 2019 at 23:54:26 labeled as SPS08090d

08.0.90T211, size=28660224

08.0.90T213, size=32539748

[Jayavidhya]

Hi @ahalper0227 

Thanks for your response.

For further troubleshooting steps please share the output of the following commands.

Show inline power

Show interface brief

Please let us know if you have any queries in this regard.

Best regards,

Jayavidhya

Lennar Home Community
 

[ahalper0227]

Update: I was able to test a ethernet direct cable from switch to computer and that resulted in high speed matching that of directly from the router.  This said it appears to be something from the switch to the access points (there are 2).  I have tested each access point individually (unplugging one at a time) and they result in the same slow speed.  What can I try next?

[Jayavidhya]

Hi @ahalper0227 

Thanks for the detailed information.

To solve this issue please check whether the cable is in good condition or not.  Also please share the output of the below commands.

Show inline power

Show interface brief

Please let us know if you have any queries in this regard.

Best regards,

Jayavidhya

Lennar Home Community
 

[ahalper0227]

All the cables look fine, no damage noted.

Inline Power:

Configure Inline PowerInline Power:Allocate Power By:Priority:

Disable X	Enable
Class:  0-UnknownClass 1-Class1 2-Class2 3-Class3 4-Class4	Power Limit: 1000
3-Lowest 2-Middle 1-Highest

Select PoE PortsSelect a rangeSelect one port (none selected)

From:  1/1/1 1/1/2 1/1/3 1/1/4 1/1/5 1/1/6 1/1/7 1/1/8 1/1/9 1/1/10 1/1/11 1/1/12   To:  1/1/1 1/1/2 1/1/3 1/1/4 1/1/5 1/1/6 1/1/7 1/1/8 1/1/9 1/1/10 1/1/11 1/1/12

1/1/1 1/1/2 1/1/3 1/1/4 1/1/5 1/1/6 1/1/7 1/1/8 1/1/9 1/1/10 1/1/11 1/1/12

Inline Power Statistics

Power Supply total capacity is 124000 of which 93200 is currently available. Power has been successfully allocated 21 times.

Inline Power Port StatisticsPortStatePower (mWatts)PDPriorityFault
ErrorAdminOperConsumedAllocatedTypeClassPortStatePower (mWatts)PDPriorityFault
ErrorAdminOperConsumedAllocatedTypeClass

1/1/1	On	Non-PD	0	0	n/a	n/a	Lowest	n/a
1/1/2	On	Off	0	0	n/a	n/a	Lowest	n/a
1/1/3	On	Off	0	0	n/a	n/a	Lowest	n/a
1/1/4	On	On	3300	15400	802.3af	Class 3	Lowest	n/a
1/1/5	On	On	3400	15400	802.3af	Class 3	Lowest	n/a
1/1/6	On	Off	0	0	n/a	n/a	Lowest	n/a
1/1/7	On	Off	0	0	n/a	n/a	Lowest	n/a
1/1/8	On	Off	0	0	n/a	n/a	Lowest	n/a
1/1/9	On	Off	0	0	n/a	n/a	Lowest	n/a
1/1/10	On	Off	0	0	n/a	n/a	Lowest	n/a
1/1/11	On	Off	0	0	n/a	n/a	Lowest	n/a
1/1/12	On	Off	0	0	n/a	n/a	Lowest	n/a

General PoE DataFirmware Version

02.1.1

Cumulative Port State DataStack Unit:Slot#PortsAdmin-OnAdmin-OffOper-OnOper-OffOff-DeniedOff-No-PDOff-Fault

SU1:S1

12

0

2

10

0

9

0

Cumulative Port Power DataStack Unit:Slot#PortsPower Consumption
in WattsPower Allocation
in WattsPri: 1Pri: 2Pri: 3

SU1:S1

0

0

12

7.400

30.800

Interface Brief:

I cannot find this in the web GUI (the only way I've been able to get to the switch).  Which menu item do you need from the GUI?