Have a power Outage and my AP's are not powering up. I have access to SWITCH ICX7150

[Swarupbade]

Have a power Outage and my AP's are not powering up. I have access to SWITCH ICX7150

[Jayavidhya · Accepted solution]

Hi @Swarupbade 

Thanks for your reply,

Based on your description, it shows that PoE is in disabled state. Please follow the below steps to enable PoE.

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-enable-PoE-or-gather-...

Please let us know if you have any queries in this regard.

Best regards,

Jayavidhya

Lennar Home Community
 

[Jayavidhya · Accepted solution]

Hi @Swarupbade 

Please try unplugging and plug the AP which is blinking red. If this step doesnot work please perform a factory reset, let me add the steps, if the Access point still not responding, please reply with a picture showing that the PWR is red.

Physical Factory Reset an Access Points Ruckus

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Physical-Factory-Reset-an-Ac...

How to factory reset or factory default different types of Ruckus Access points? (technical guide.)

https://support.ruckuswireless.com/articles/000012418

Best regards,

Jayavidhya

Lennar Home Community
 

[Jayavidhya]

Hi @Swarupbade 

Greetings of the day,

1-On your switch while it's plugged into the outlet, do you see any lights on? (Amber or green) Please let us know which lights are on? 

https://docs.commscope.com/bundle/icx7150-installguide/page/GUID-973C8AE8-837A-41C7-9811-BAEF6ADEF3D...

2- Make sure it is plugged into a well-known outlet/power source

Best regards,

Jayavidhya

Lennar Home Community
 

[Swarupbade]

it's green, i just confirmed

[Swarupbade]

My switch is ICX 7150-C12P

based on pic you sent, I have 7 (Sys) and 16 (PWR) both Green. The only issue is with the Access point  not receiving power. I see that ring which is connected to one of the ports in the switch is working. Also, I am sure the ATT router internet is working, as I am currently using it. Please let me know how to power up the AP. Thanks.

[Swarupbade]

telnet@ICX7150-C12 Switch>enable
No password has been assigned yet...
telnet@ICX7150-C12 Switch#show version
Copyright (c) 1996-2017 Brocade Communications Systems, Inc. All rights reserved.
UNIT 1: compiled on Aug 14 2017 at 06:54:44 labeled as SPS08061a
(24723488 bytes) from Primary
SW: Version 08.0.61aT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.10T225 (mnz10110)
Compiled on Sun Jun 25 09:25:15 2017

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3204P0WH
Current License:
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 20 hour(s) 43 minute(s) 17 second(s)
The system started at 00:02:05 GMT+00 Sat Jan 01 2000

The system : started=cold start

telnet@ICX7150-C12 Switch#show inline power

Power Capacity: Total is 124000 mWatts. Current Free is 124000 mWatts.

Power Allocations: Requests Honored 0 times

Port Admin Oper ---Power(mWatts)--- PD Type PD Class Pri Fault/
State State Consumed Allocated Error
--------------------------------------------------------------------------
1/1/1 Off Off 0 0 n/a n/a 3 n/a
1/1/2 Off Off 0 0 n/a n/a 3 n/a
1/1/3 Off Off 0 0 n/a n/a 3 n/a
1/1/4 Off Off 0 0 n/a n/a 3 n/a
1/1/5 Off Off 0 0 n/a n/a 3 n/a
1/1/6 Off Off 0 0 n/a n/a 3 n/a
1/1/7 Off Off 0 0 n/a n/a 3 n/a
1/1/8 Off Off 0 0 n/a n/a 3 n/a
1/1/9 Off Off 0 0 n/a n/a 3 n/a
1/1/10 Off Off 0 0 n/a n/a 3 n/a
1/1/11 Off Off 0 0 n/a n/a 3 n/a
1/1/12 Off Off 0 0 n/a n/a 3 n/a
--------------------------------------------------------------------------
Total 0 0

telnet@ICX7150-C12 Switch#show inline power detail

Power Supply Data On unit 1:
++++++++++++++++++

Power Supply Data:
++++++++++++++++++

Power Supply #1:
Max Curr: 2.3 Amps
Voltage: 54.0 Volts
Capacity: 124 Watts
PoePower: 124 Watts

POE Details Info. On Unit 1 :

General PoE Data:
+++++++++++++++++

--More--, next page: Space, next line: Return key, quit: Control-c