cancel
Showing results for 
Search instead for 
Did you mean: 

ICX 7150: Not letting me create a Router-Interface

jose_quiroz_eln
New Contributor II
HELP!!!

I've been trying to create a vlan with its own dhcp server, however for some reason my switch is not letting me create a router-interface. I do have the dhcp pool ready for it, though.

below is code:
ICX7150-C12 Switch(config)#vlan 30

ICX7150-C12 Switch(config-vlan-30)#tagged e 1/1/3
Added tagged port(s) ethe 1/1/3 to port-vlan 30.

ICX7150-C12 Switch(config-vlan-30)#tagged e 1/1/4
Added tagged port(s) ethe 1/1/4 to port-vlan 30.

ICX7150-C12 Switch(config-vlan-30)#untagged e 1/1/5
Added untagged port(s) ethe 1/1/5 to port-vlan 30.

ICX7150-C12 Switch(config-vlan-30)#router-interface ve 30
Invalid input -> router-interface ve 30
Type ? for a list

ICX7150-C12 Switch(config-vlan-30)#exit

ICX7150-C12 Switch(config)#show run
Current configuration:
!
ver 08.0.70cT211
!
stack unit 1
  module 1 icx7150-c12-poe-port-management-module
  module 2 icx7150-2-copper-port-2g-module
  module 3 icx7150-2-sfp-plus-port-20g-module
!
!
!
!
vlan 1 name DEFAULT-VLAN by port
!
vlan 30 by port
 tagged ethe 1/1/3 to 1/1/4
 untagged ethe 1/1/5
!
!
!
!
!
!
!
!
!
!
!
!
!
aaa authentication web-server default local
aaa authentication login default local
dhcp-gateway-list 10 192.168.30.1
ip address 192.168.1.90 255.255.255.0
no ip dhcp-client enable
ip dhcp-server enable
!
ip dhcp-server pool testvlan30
 excluded-address 192.168.30.1
 lease 1 0 0
 network 192.168.30.0 255.255.255.0
 option  3 ip 192.168.30.1
 deploy
!
!
username telepro password .....
username user password .....
username ruckus password .....
username admin password .....
!
!
interface ethernet 1/3/1
 speed-duplex 1000-full
!
interface ethernet 1/3/2
 speed-duplex 1000-full
!
!
!
!
!
!
!
!
!
end

21 REPLIES 21

Thanks so muchhhhh. You saved my whole day 😄

jon_maiman_iyni
New Contributor III
Please capture the output from the following commands and post it to the thread:

Skip
Show run
Show Version
Show Ip Int
Show Ip Route
page

Best guess without more information is you don't have a "WAN" IP address for the port connected to the Internet.   Since the ICX7150 is running router code, you need to be able to route up to the Internet.   Second guess is your Upstream Internet Router doesn't have routes back to your ICX7150 for the locally hosted subnets you created.   The output from the above commands should help isolate the problem.

--Jon

please see below:

ICX7150-C12 Router(config)#skip
Invalid input -> skip
Type ? for a list



ICX7150-C12 Router(config)#show run
Current configuration:
!
ver 08.0.70cT213
!
stack unit 1
  module 1 icx7150-c12-poe-port-management-module
  module 2 icx7150-2-copper-port-2g-module
  module 3 icx7150-2-sfp-plus-port-20g-module
!
!
global-stp
!
!
!
vlan 1 name DEFAULT-VLAN by port
!
vlan 2 name IP-Subnet_10.1.2.0/24 by port
!
vlan 30 by port
 untagged ethe 1/1/6 to 1/1/12
 router-interface ve 30
!
!
!
!
!
!
!
!
!
!
!
!
!
aaa authentication web-server default local
aaa authentication login default local
boot sys fl sec
ip dhcp-server enable
!
ip dhcp-server pool testvlan30
 excluded-address 192.168.30.1
 lease 1 0 0
 network 192.168.30.0 255.255.255.0
 option  3 ip 192.168.30.1
 deploy
!
ip route 192.168.30.0/24 192.168.1.254
!
username telepro password .....
username user password .....
username ruckus password .....
username admin password .....
!
!
!
!
!
!
!
!
!
interface ethernet 1/3/1
 speed-duplex 1000-full
!
interface ethernet 1/3/2
 speed-duplex 1000-full
!
interface ve 30
 ip address 192.168.30.1 255.255.255.0
!
!
!
!
!
!
!
!
!
!
end



ICX7150-C12 Router(config)#Show Version
  Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
    UNIT 1: compiled on Aug 30 2018 at 04:48:29 labeled as SPR08070c
      (29437672 bytes) from Secondary SPR08070c.bin
        SW: Version 08.0.70cT213
      Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225 (mnz10113)
       Compiled on Tue Jul 24 10:23:08 2018

  HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
      Serial  #:FEK3811Q1WN
      Current License: 2X1G
      P-ASIC  0: type B160, rev 11  Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
 1000 MHz ARM processor ARMv7 88 MHz bus
 8192 KB boot flash memory
 2048 MB code flash memory
 1024 MB DRAM
STACKID 1  system uptime is 38 minute(s) 25 second(s)
The system started at 00:01:54 GMT+00 Sat Jan 01 2000

The system : started=cold start



ICX7150-C12 Router(config)#Show Ip Int
Interface           IP-Address      OK?  Method    Status             Protocol   VRF
Ve 30               192.168.30.1    YES  NVRAM     up                 up         default-vrf



ICX7150-C12 Router(config)#Show Ip Route
Total number of IP routes: 1
Type Codes - B:BGP D:Connected O:OSPF R:RIP S:Static; Cost - Dist/Metric
BGP  Codes - i:iBGP e:eBGP
OSPF Codes - i:Inter Area 1:External Type 1 2:External Type 2
        Destination        Gateway         Port          Cost          Type Uptime
1       192.168.30.0/24    DIRECT          ve 30         0/0           D    39m7s



ICX7150-C12 Router(config)#page
Invalid input -> page
Type ? for a list

jose_quiroz_eln
New Contributor II
please see below:

ICX7150-C12 Router(config)#skip
Invalid input -> skip
Type ? for a list



ICX7150-C12 Router(config)#show run
Current configuration:
!
ver 08.0.70cT213
!
stack unit 1
  module 1 icx7150-c12-poe-port-management-module
  module 2 icx7150-2-copper-port-2g-module
  module 3 icx7150-2-sfp-plus-port-20g-module
!
!
global-stp
!
!
!
vlan 1 name DEFAULT-VLAN by port
!
vlan 2 name IP-Subnet_10.1.2.0/24 by port
!
vlan 30 by port
 untagged ethe 1/1/6 to 1/1/12
 router-interface ve 30
!
!
!
!
!
!
!
!
!
!
!
!
!
aaa authentication web-server default local
aaa authentication login default local
boot sys fl sec
ip dhcp-server enable
!
ip dhcp-server pool testvlan30
 excluded-address 192.168.30.1
 lease 1 0 0
 network 192.168.30.0 255.255.255.0
 option  3 ip 192.168.30.1
 deploy
!
ip route 192.168.30.0/24 192.168.1.254
!
username telepro password .....
username user password .....
username ruckus password .....
username admin password .....
!
!
!
!
!
!
!
!
!
interface ethernet 1/3/1
 speed-duplex 1000-full
!
interface ethernet 1/3/2
 speed-duplex 1000-full
!
interface ve 30
 ip address 192.168.30.1 255.255.255.0
!
!
!
!
!
!
!
!
!
!
end



ICX7150-C12 Router(config)#Show Version
  Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
    UNIT 1: compiled on Aug 30 2018 at 04:48:29 labeled as SPR08070c
      (29437672 bytes) from Secondary SPR08070c.bin
        SW: Version 08.0.70cT213
      Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225 (mnz10113)
       Compiled on Tue Jul 24 10:23:08 2018

  HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
      Serial  #:FEK3811Q1WN
      Current License: 2X1G
      P-ASIC  0: type B160, rev 11  Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
 1000 MHz ARM processor ARMv7 88 MHz bus
 8192 KB boot flash memory
 2048 MB code flash memory
 1024 MB DRAM
STACKID 1  system uptime is 38 minute(s) 25 second(s)
The system started at 00:01:54 GMT+00 Sat Jan 01 2000

The system : started=cold start



ICX7150-C12 Router(config)#Show Ip Int
Interface           IP-Address      OK?  Method    Status             Protocol   VRF
Ve 30               192.168.30.1    YES  NVRAM     up                 up         default-vrf



ICX7150-C12 Router(config)#Show Ip Route
Total number of IP routes: 1
Type Codes - B:BGP D:Connected O:OSPF R:RIP S:Static; Cost - Dist/Metric
BGP  Codes - i:iBGP e:eBGP
OSPF Codes - i:Inter Area 1:External Type 1 2:External Type 2
        Destination        Gateway         Port          Cost          Type Uptime
1       192.168.30.0/24    DIRECT          ve 30         0/0           D    39m7s



ICX7150-C12 Router(config)#page
Invalid input -> page
Type ? for a list



jon_maiman_iyni
New Contributor III
As I suspected, you don't have a "WAN" IP Address to your upstream Internet Router.    From when you connected your laptop to the Internet directly, your IP Subnet for the Internet is 192.168.1.0/24 and your gateway (next hop) is 192.168.1.254.    You can create a VE in VLAN 1 (the default VLAN) and have it get an address via DHCP.   The config. would be approx.:

vlan 1
router-interface ve 1

interface ve 1
ip dhcp-client

You will still need the default route to the internet:

ip route 0.0.0.0/0 192.168.1.254

However, this only fixes the problem in one direction (sending traffic upstream to the Internet).   You will need a route on your Internet Gateway pointing to your ICX switch for the 192.168.30.0/24 network for downstream traffic.

This begs the question, if you only plan on having one IP Subnet 192.168.30.0 on your ICX Switch, why are you running router code?   Wouldn't it be simpler to just use your switch as layer 2 only and configure your Internet Gateway to handout addresses in the 192.168.30.0 subnet for clients?   Since the Internet Traffic will be NAT'ed anyway, you really could just leave the DHCP clients be assigned in the 192.168.1.0 subnet your Internet Gateway is already configured for.

--Jon