Different dataplane firmware version after replacing SCG200 in a cluster
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-18-2020 10:42 AM
We have clustered two SCG 200 and due to a failure in a dataplane we have replace the faulty unit to a new SCG200. After integrating the new device with working SCG ( before replace the new device firmware has upgrade to compatible with the existing SCG) we see the dataplane firmware is different with the existing SCG. New SCG dataplane firmware version is lower than the older SCG dataplane. Need to know why there is a difference?
Command show version output same version in both SCGs, but under cluster planes it shows different firmware versions in dataplane.
Command show version output same version in both SCGs, but under cluster planes it shows different firmware versions in dataplane.
2 REPLIES 2
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-18-2020 01:12 PM
I don't know how physical controller SCG200 with built-in dataplane can have different than controller version.
What version of code are you running please? What info are you seeing with differing DP version (I may not
be aware of)?
In latest SmartZone releases for SCG200, the SCG and DP versions were the same. In much earlier releases
we did have different version for DP, ie.
SCG200-C
Controller Version: 3.6.2.0.250
Control Plane Software Version: 3.6.2.0.78
AP
Firmware Version: 3.6.2.0.759
and no
mention of Dataplane...
If I
look back at SZ 3.6 (GA) Release Notes I see:
SCG 200
Controller Version: 3.6.0.0.510
Control Plane Software Version: 3.6.0.0.392
AP
Firmware Version: 3.6.0.0.709
But back
to SZ 3.1.2p2 Release Notes, I see:
SCG-200
Release Information
SCG-200 system version: 3.1.2.0.536
Control plane software version: 3.1.2.0.514
Data
plane software version: 3.1.2.0.521
AP
firmware version: 3.1.2.0.150
What version of code are you running please? What info are you seeing with differing DP version (I may not
be aware of)?
In latest SmartZone releases for SCG200, the SCG and DP versions were the same. In much earlier releases
we did have different version for DP, ie.
SCG200-C
Controller Version: 3.6.2.0.250
Control Plane Software Version: 3.6.2.0.78
AP
Firmware Version: 3.6.2.0.759
and no
mention of Dataplane...
If I
look back at SZ 3.6 (GA) Release Notes I see:
SCG 200
Controller Version: 3.6.0.0.510
Control Plane Software Version: 3.6.0.0.392
AP
Firmware Version: 3.6.0.0.709
But back
to SZ 3.1.2p2 Release Notes, I see:
SCG-200
Release Information
SCG-200 system version: 3.1.2.0.536
Control plane software version: 3.1.2.0.514
Data
plane software version: 3.1.2.0.521
AP
firmware version: 3.1.2.0.150
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-21-2020 11:18 PM
Hi Michael,
On both SCG200 s the firmware version same as below.
Model : SCG200
SCG Version : 3.4.2.0.176
Control Plane Software Version : 3.4.2.0.93
Data Plane Software Version : 3.4.2.0.118
AP Firmware Version : 3.4.2.0.384
But when check the Dataplance firmware version from cluster plane is different.

Regards,
Ashan
On both SCG200 s the firmware version same as below.
Model : SCG200
SCG Version : 3.4.2.0.176
Control Plane Software Version : 3.4.2.0.93
Data Plane Software Version : 3.4.2.0.118
AP Firmware Version : 3.4.2.0.384
But when check the Dataplance firmware version from cluster plane is different.
Regards,
Ashan

