This website uses cookies. By clicking Accept, you consent to the use of cookies. Click Here to learn more about how we use cookies.
Accept
Reject
RUCKUS Self Help |   ASK the Pack
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 

Ruckus ICX 7150-C12P not sending power to R510 AP's

Go to solution
pramod_gujjar
New Contributor II

‎01-12-2023 10:18 AM

Hi,

I see that my Ruckus ICX 7150-C12P installed by Lennar is not sending any power to R510 AP's.

I see only 2 lights on the switch one is PWR and SYST, but none of the APs plugged in have no light.

Please let me know how to fix this. 

Thank you so muchIMG_7173.jpg

1 ACCEPTED SOLUTION

Go to solution
Vásquez_Fer
Moderator
Moderator
In response to pramod_gujjar

‎01-31-2023 11:43 AM - edited ‎01-31-2023 11:52 AM

Hi @pramod_gujjar 

Hope you are doing great !

As I can see, according to the color lights of your Switch (ICX-7150) is stuck in boot mode stage.

That does not mean is broken or need to be replace 'in some cases'

When the switch is in boot mode ,  it will not show up in the IP scanner,  since it cannot get a valid IP address , to access Switch when is on boot mode , we will need a console connection, it can be using a USB type C to USB cable.

Software recovery Process 

If resetting the Switch does not work , we need to perform a software recovery process since it can be that the image flash is corrupted so in basic words the unit is not able to boot up properly and need re-install the image ( software version )  to boot up the unit properly.

1-We need to access (physical) using one of the cables to the ICX-7150-C12P mentioned on the below guide: 

How to console in the ICX-7150-12cp 

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-console-in-the-ICX-71...

Here is the Guide how to preform the Software Recovery process correctly to boot up the switch  and the video Link

 https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-a-Software-r...

 Video Link: https://www.youtube.com/watch?v=Ql22blH_CGo

Best Regards 

Fernando Vasquez 

View solution in original post

0 Kudos
11 REPLIES 11

Go to solution
pramod_gujjar
New Contributor II

‎01-12-2023 10:20 AM

Also, I am unable to login into the Unleashed network to see the status of the switch. 

0 Kudos

Go to solution
Jayavidhya
Moderator
Moderator
In response to pramod_gujjar

‎01-12-2023 11:07 AM - edited ‎01-12-2023 11:07 AM

Hi @pramod_gujjar

Basically if the switch has one green and one yellow light, it means that the switch is stuck in boot mode.

1-Please try to disconnect from the Power outlet the ICX-7150 and reconnect it.

2-Please try to press the reset button using a paper click or a small stick 

  1. Remove power from the switch.
  2. Press and hold the Reset button while applying power to the switch.
  3. After all the system LEDs flash amber, release the Reset button.

https://docs.commscope.com/bundle/icx7150-installguide/page/GUID-D3B5DB74-53A7-4F8D-82F9-6EB600879EE...

Video link:https://www.youtube.com/watch?v=6jHMTdo_hK4

If this step doesn't work, we need to perform a software recovery.

Here is the quick guide to perform software recovery.

How to perform a Software recovery on an ICX7150 switch

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-a-Software-re...

Ruckus ICX Recovery Load boot code from boot monitor

https://www.youtube.com/watch?v=RHriOYYD_iI&t=7s

Note: after fixing the issue of the Switch been stuck in boot mode, please perform an upgrade to the code 08095g UFI and upgrade both partitions with the switching code file named SPS08095gufi.bin, so perform the software recovery using the code 08090k with the upgrade image file named SPS08090k.bin, then when the switch is back to normal upgrade to the file SPS08095gufi.bin for both partitions primary and secondary.

1.Upgrade a Switch ICX-7150-C12P using a USB flash drive

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

  1. Upgrade a Switch ICX7150-C12P via TFTP

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

  1. Upgrade a switch via Web GUI (ICX7150 Switch)

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-an-Upgrade-vi...

Best regards,

Jayavidhya

Lennar Home Community

0 Kudos

Go to solution
pramod_gujjar
New Contributor II

‎01-18-2023 08:04 AM

@Jayavidhya, I followed the above steps but I am unable to get a ping from the Switch to perform a Software recovery on an ICX7150 switch. Followed step 2 of recovery. The putty never shows the boot prompt to enter any command. 

I think there is something wrong with the switch as a whole and please send a replacement switch.

Thanks

Pramod Gujjar

0 Kudos

Go to solution
Jayavidhya
Moderator
Moderator
In response to pramod_gujjar

‎01-18-2023 08:24 AM

Hi @pramod_gujjar

Please provide an image/photo where you are trying to connect via console from ICX 7150 - C12 P (USB type C to  USB ) to PC. Before uploading the photos please login to the RUCKUS account and you can upload the image.

Jayavidhya_0-1674058998508.png

Best regards,

Jayavidhya

Lennar Home Community

 

0 Kudos
Labels
Copyright © 2024 Khoros, LLC