09-03-2024 03:34 PM
Hi,
I am having this same problem ("PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power."). The APs started to sporadically lose POE after a power outage.
I started down this path:How to Upgrade a Switch ICX-7150-C12P using a USB flash drive
However, after the first reboot I have lost access to the console due to constant POE error messages.
I have tried both methods referenced above to "To disable the logs for the PoE error, run the next commands."
Neither worked.
I made to this step (20- Once the switch is running 8080f version, we can proceed to install the 8095hufi, in this version as I mentioned previously, the boot code is not needed to be install separately since it is included in the same file.) but can't really verify versions etc. since my console filled with errors.
What should I try next?
09-04-2024 07:20 AM
Hi @lenar_ruck_user ,
Greetings!
Thank you for contacting RUCKUS Lennar Home Community.
I hope you are doing well!!!
Thank you for the information you shared.
From the case description, I understand that you are facing issues with PoE on the Switch after the power outage.
Before we can help, we need to check which version the Switch is currently running.
Please follow the below steps and help us with the queries,
1. To check this, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P
I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily.
How to find the IP Address of the RUCKUS Devices (Switch and APs) using IP Scanner free applications:
2. Once we identify the IP address of the switch proceed to access remotely to the device “Command Line”
If you can access the Command line should look like this:
ICX7150-C12 Router> OR
ICX7150-C12 Switch>
Please enter the below commands once you log in to CLI and share the output.
Note: Hit Enter to accept each command
enable
show version
show flash
Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.
Thank you again. We appreciate your patience and understanding.
Best regards,
Pinky Rajendran
RUCKUS Lennar Home Community.
09-04-2024 07:49 PM
Thank you Pinky!
I was able to continue on the upgrade path and it seems that has fixed my POE issues... APs back online. Here is the output you requested:
telnet@ICX7150-C12-Switch#show version
show version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Aug 26 2022 at 01:20:24 labeled as SPS08095h
(31457280 bytes) from Secondary SPS08095h.bin (UFI)
SW: Version 08.0.95hT211
Compressed Secondary Boot Code size = 786944, Version:10.1.25T225 (mnz10125)
Compiled on Mon Aug 8 11:58:28 2022
HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3203P15R
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8 MB boot flash memory
2 GB code flash memory
1 GB DRAM
--More--, next page: Space, next line: Return key, quit: Control-c
STACKID 1 system uptime is 28 minute(s) 43 second(s)
The system started at 01:20:25 GMT+00 Fri Aug 26 2022
The system : started=warm start reloaded=by "reload"
telnet@ICX7150-C12-Switch#
telnet@ICX7150-C12-Switch#
telnet@ICX7150-C12-Switch#show flash
show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 31457280, Version:08.0.95hT211 (SPS08095h.bin)
Compressed Sec Code size = 31457280, Version:08.0.95hT211 (SPS08095h.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.25T225 (mnz10125)
Compressed Sec Boot Code size = 786944, Version:10.1.25T225 (mnz10125)
Code Flash Free Space = 1111756800
telnet@ICX7150-C12-Switch#show poe
show poe
Power Capacity: Total is 124000 mWatts. Current Free is 77800 mWatts.
Power Allocations: Requests Honored 15 times
Port Admin Oper ---Power(mWatts)--- PD Type PD Class Pri Fault/
State State Consumed Allocated Error
-----------------------------------------------------------------------------
1/1/1 On On 3400 15400 2P-IEEE Class 3 3 n/a
1/1/2 On On 3300 15400 2P-IEEE Class 3 3 n/a
1/1/3 On Off 0 0 n/a n/a 3 n/a
1/1/4 On On 2100 15400 2P-IEEE n/a 3 n/a
1/1/5 On Off 0 0 n/a n/a 3 n/a
1/1/6 On Off 0 0 n/a n/a 3 n/a
1/1/7 On Off 0 0 n/a n/a 3 n/a
1/1/8 On Off 0 0 n/a n/a 3 n/a
1/1/9 On Off 0 0 n/a n/a 3 n/a
1/1/10 On Off 0 0 n/a n/a 3 n/a
1/1/11 On Non-PD 0 0 n/a n/a 3 n/a
1/1/12 On Off 0 0 n/a n/a 3 n/a
-----------------------------------------------------------------------------
Total 8800 46200
--More--, next page: Space, next line: Return key, quit: Control-c
Follow-up Questions:
Thanks again for the help, much appreciated!
09-05-2024 09:51 AM
Hello @lenar_ruck_user ,
Thank you for the response.
We are glad to know that the Poe issue has been resolved after the upgrade has been performed.
I understand you have few follow-up questions and am glad to address all your queries.
1. Upon checking the output you shared, I see that the Switch is in the latest version (08.0.90h) and you do not have to perform Firmware upgrade on the Switch currently.
As you have accessed the CLI of the Switch using the Telnet option, you can go ahead and reset the Switch credentials using the following commands.
Once you are able to access the CLI, I would request you to please execute the following commands to reset the Switch login credentials.
ICX7150-12P Switch>enable
ICX7150-12P Switch#configure terminal
ICX7150-12P Switch# username super password pass
Where the username is ’super’ and password ‘pass’ (You could choose any of your choices)
To allow the correct authentication please run the following commands:
ICX7150-12P Switch (config)#crypto key generate rsa
ICX7150-12P Switch (config)# aaa authentication login default local
ICX7150-12P Switch (config)# aaa authentication web-server default local
2. As you have the Ip address of the Access points, you do not have to login using ssh or http. You may please log in to your Unleashed system on a LAPTOP WEB BROWSER using the Master AP IP Address OR https://unleashed.ruckuswireless.com/
.Please try to use the default combination credentials as mentioned below to login to the Ap using browser or through app.
3. We suggest you upgrade your ALL RUCKUS R510 Access Points to version 200.15.6.12.304 which is recently released.
Please follow the below RUCKUS Lennar Knowledge base self-help article which will help you to upgrade the Ruckus AP to a recommended version.
4. There are no security or hardening guidelines for the setup. However, for guidance on setting up your system, please refer to the RUCKUS Lennar Knowledge Base self-help article linked below. The article includes detailed instructions for the setup process.
Please follow the steps and let me know if you have any queries in this regard.
Thank you again for your patience.
Best regards,
Pinky Rajendran
RUCKUS Lennar Home Community.
09-12-2024 12:50 PM
Thanks Pinky! Unfortunately, none of these credentials worked on the web login. What do you recommend?
Thanks.