CommScope RUCKUS Community Forums

kirsteng003 · ‎12-28-2022

The WiFi through our Ruckus Access Points will go out multiple times through out the day while I know our internet is not out as I check through our xfinity app and the WiFi through the router is working fine, however, it doesn't reach to my office (hence the access points). Any thoughts of what could be causing this and how to fix it?

Yarenis · ‎12-28-2022

Hi @kirsteng003

Base in your description, it looks like your Switch (ICX7150 Switch) may be booting from the wrong partition, let me add the guide to fix the issue.

Note: if you have access to the Unleashed Dashboard and the Switch can be seen from there, it may look like the following image, ICX7150-C12-Router instead of ICX7150-C12-Switch, now before starting the steps of the guide, I will advise you to cable the computer directly to the Switch, since you will have a better connectivity than if you connect via wireless, final after fixing the issue, please perform an upgrade to the code 08095g UFI and upgrade both partitions with the switching code file named SPS08095gufi.bin, take in consideration that if you are running a code lower that 08080f, you must upgrade twice, using the next path.

Code you are>>08080f>>>08095g UFI

How to Fix Routing code issues on Lennar Home users via Web GUI.

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

How to Fix Routing code issues on Lennar Home users via CLI

Guide#1:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

Guide#2:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-solve-the-routing-cod...

How to Upgrade a Switch ICX-7150-C12P using a USB flash drive

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

How to upgrade a Switch ICX7150-C12P via TFTP

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

Best regards,

Yarenis Hernández.

Technical Support Engineer | L2 TAC Wired | Lennar Home Community

kirsteng003 · ‎01-03-2023

Thank you so much for your detailed reply. It does sound like that could be the issues, especially since this started to occur after an outage due to power blink. I have identified the IP address of the switch but cannot seem to access the dashboard by searching the IP address in my web browser. Is there any further support that can be offered?

kirsteng003 · ‎01-03-2023

@Yarenis

Thank you so much for your detailed reply. It does sound like that could be the issues, especially since this started to occur after an outage due to power blink. I have identified the IP address of the switch but cannot seem to access the dashboard by searching the IP address in my web browser. Is there any further support that can be offered?

Yarenis · ‎01-03-2023

Hi @kirsteng003

If the Switch IP address does not bring you to the WEB GUI of the Switch, you can try the SSH or TELNET access with the same IP address if the issue, persisted, your only option will be the console access and follow up one of the two guides to fix the routing code issue via CLI.

1:SSH or Telnet access with the IP address you have found.

How to remotely access to 'ICX 7150-12P' or 'access points' "Network devices"

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-IC...

2:If still not working, you need you gain access via console.

How to console in the ICX-7150-12CP 'Ruckus Switch'

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-console-in-the-ICX-71...

RUCKUS ICX 7150 USB TYPE C CONSOLE (tutorial video for ICX)

https://www.youtube.com/watch?v=YXR4xhkw3q8

(Tutorial for MAC)

https://www.youtube.com/watch?v=1AcJokMm78U

3:Once you gained access, follow up one of the next two guides

How to Fix Routing code issues on Lennar Home users via CLI