01-10-2023 09:45 AM
When I bought my lennar home, it came with a ruckus ICX7150-C12 Switch and a couple of AP. Yesterday without any reason the switch stopped sending power to the devices I have that need PoE. Both APs and my ring.
I accessed the console using putty and reboot the switch (multiple times) and every time at some point during the booting I start getting error:
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
non stop. Tried ctrl+c, quit, q!, exit…
How can I stop this non stop error message to be able to troubleshoot?
01-10-2023 11:25 AM
Hi @ingosds
For better understanding please share the below details.
Show version
Show inline power
Show inline power detail
Best regards,
Jayavidhya
Lennar Home Community
01-13-2023 04:12 PM
1-Please try to disconnect from the Power outlet the ICX-7150 and reconnected.
- Done 2 times. No luck
2-Please try to press the reset button using a paper click or a small stick
Remove power from the switch. Press and hold the Reset button while applying power to the switch. After all the system LEDs flash amber, release the Reset button.
- For some reason I cannot factory reset the switch. I press the reset button, power back on while still holding the reset button and I dont get the blinking orange lights.
3-We need to access (physical) using one of the cables to the ICX-7150C12P mentioned on the below guide:
- I had access to the console already. This is the part that I cannot make the error message:
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
stop showing. I tried to do: enable > configuration enable > no logging on and that did not work as well.
Invalid input -> Boot_primary
Type ? for a list
ICX7150-C12 Switch>PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
PoE Fatal: Vmain (48V) fault has
*More about the error I am experiencing during boot:
The system : started=cold start
ICX7150-C12 Switch>
PS 1, Internal Power supply detected.
PS 1, Internal Power supply is up.
PoE Info: Adding new 54V capacity of 124000 mW, total capacity is 124000, total free capacity is 124000
ICX7150-C12 Switch>PoE: Port 1/1/4 found non-PD during init, so will disable PD detection.
PoE: Port 1/1/6 found non-PD during init, so will disable PD detection.
PoE Info: PoE module 1 of Unit 1 on ports 1/1/1 to 1/1/12 detected. Initializing....
2000 log entries of PoE Event Trace Log Buffer is allocated on unit 1 for unit 1
PoE Event Trace Logging enabled for unit 1
PoE Info: PoE module 1 of Unit 1 initialization is done.
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
01-13-2023 04:14 PM
Entire Boot:
Brocade Bootloader: 10.1.10T225 (Jun 25 2017 - 02:25:01 -0700)
Booted from partition 2
DRAM: Validate Shmoo parameters stored in flash ..... OK
ICX7150-12 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0x7
device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
device 0 offset 0x0, size 0xc0000
bootdelay: ===
Booting image from Primary
NAND read: device 0 offset 0x0, size 0x2000000
33554432 bytes read: OK
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Brocade Linux MN
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x70208ed8
Data Size: 2147480 Bytes = 2 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: bd1305db
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Brocade Linux MN
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x70208ed8
Data Size: 2147480 Bytes = 2 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: bd1305db
Verifying Hash Integrity ... crc32+ OK
## Loading ramdisk from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'ramdisk@1' ramdisk subimage
Description: Ramdisk -rootfs
Type: RAMDisk Image
Compression: lzma compressed
Data Start: 0x7041bd88
Data Size: 20409303 Bytes = 19.5 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Hash algo: crc32
Hash value: dec09c53
Verifying Hash Integrity ... crc32+ OK
## Loading fdt from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'fdt@3' fdt subimage
Description: Flattened Device Tree blob - Minion.dtb
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x70419af0
Data Size: 8669 Bytes = 8.5 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 20f90d3c
Verifying Hash Integrity ... crc32+ OK
Loading fdt from 0x70419af0 to 0x65008000
Booting using the fdt blob at 0x65008000
Uncompressing Kernel Image ... OK
Using Device Tree in place at 65008000, end 6500d1dc
Starting kernel ...
booting with 4.4 kernel
dd cmd: UBI
Config partition mounted
Resource partition is mounted!!
Starting TPM Infra
Group tss and User tss created
kernel.hostname = localhost
hostname set to localhost
Starting TCSD Daemon
TCSD Up and Running
dma_mem_base: 0x96000000, dma_mem_len: 0x8000000, warm_mem_base: 0x9f500000, warm_mem_len: 0xb00000
Creating TUN device
Dumping the partition's content …
Dumping the partition's content ...
^[Starting the FastIron. WARNING!!! === Heap Memory debug has been enabled ===
i2c-0 i2c Broadcom iProc I2C adapter I2C adapter 2
i2c-1 i2c Broadcom iProc I2C adapter I2C adapter 2
FIPS Disabled:PORT NOT DISABLED
platform type 90
OS>
Loaded Image SPS08061a from Pri Built on (UTC): Mon Aug 14 13:59:15 2017
set_board_level: gi_board_type = 116DMA pool size: 134217728
PHY Reset De-asserted
sw_pp_sdk_init:114 ToR init for Minion Board
SOC unit 0 attached to PCI device BCM56160_B0
Pre Parsing Config Data ...
Warning: This operation would close all existing SSH connection.
Parsing Config Data ...
Hotplugger Daemon Initialized ..
8.0M initramfs-new.cpio.lzo
System initialization completed...console going online.
Copyright (c) 1996-2017 Brocade Communications Systems, Inc. All rights reserved.
UNIT 1: compiled on Aug 14 2017 at 06:54:44 labeled as SPS08061a
(24723488 bytes) from Primary SPS08061a.bin
SW: Version 08.0.61aT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.10T225 (mnz10110)
Compiled on Sun Jun 25 09:25:15 2017
HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3205P0DM
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 18 second(s)
The system started at 00:02:06 GMT+00 Sat Jan 01 2000
The system : started=cold start
ICX7150-C12 Switch>
PS 1, Internal Power supply detected.
PS 1, Internal Power supply is up.
PoE Info: Adding new 54V capacity of 124000 mW, total capacity is 124000, total free capacity is 124000
ICX7150-C12 Switch>PoE: Port 1/1/4 found non-PD during init, so will disable PD detection.
PoE: Port 1/1/6 found non-PD during init, so will disable PD detection.
PoE Info: PoE module of Unit 1 on ports 1/1/1 to 1/1/12 detected. Initializing….
2000 log entries of PoE Event Trace Log Buffer is allocated on unit 1 for unit 1
Poe Event Trace Logging enable for unit 1
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power.
01-16-2023 12:15 PM
Hi @ingosds
I can see you are now booting properly however, I will advise performing the upgrade from the code you are to the recommended code 08095g, now like you are in a pretty old code, you need to upgrade twice, from the code you are to 08080f and then the recommended code 08095g UFI, please upgrade both partitions with the switching code file named SPS08095gufi.bin
Here are two options to perform the upgrade.
How to Upgrade a Switch ICX-7150-C12P using a USB flash drive
How to upgrade a Switch ICX7150-C12P via TFTP
Example:
1a) device# copy tftp flash 10.176.220.51 SPR08080f.bin primary
1b) device# copy tftp flash 10.176.220.51 spz10114.bin bootrom
Show flash (ensure that you have the new flash code)
Write memory
reload
Now you can go to the recommended code:
2a) device# copy tftp flash 10.176.220.51 SPR08095gufi.bin primary
device# copy tftp flash 10.176.220.51 SPR08095gufi.bin secondary
Show flash (ensure that you have the new flash code)
Write memory
Reload
Best regards,
Yarenis Hernández.
Technical Support Engineer | L2 TAC Wired | Lennar Home Community