Access points dont have power

[Willgomez845]

My access point won't turn on after a power outage both system lights are showing green not Amber so don't do the reset not sure what to do here

[Willgomez845]

[Sgatjens]

Hi @Willgomez845 

Seems that you switch may present some PoE issue (power over Ethernet)
To solve this you must access the command line of the Switch and do some diagnostics

1-For this we must locate the IP address for the Switch (this is a logical address assigned by your local router (ISP) to the switch) I will leave a quick guide: 

How to find my Ruckus “Devices IP address” using free applications

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Device...

2-After that we must remotely access to device, I leave a guide on how to access to the switch

Here is a quick guide how to access via CLI of the devices 

How to remotely access to 'ICX 7150-12P' or 'access points' "Network devices"

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-IC...

If you can access to the Command line should look like this 

ICX7150-C12 Switch>

3-Write the following commands:

Note: Hit Enter to accept each command:

ICX7150-C12 Switch>enable
ICX7150-C12 Switch#show version
ICX7150-C12 Switch#show inline power
ICX7150-C12 Switch#show inline power detail

Copy and paste the results on the chat (here) 

If you cannot access via IP we can access physical using a console cable 

How to console in the ICX-7150-C12p

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-console-in-the-ICX-71...

Once you are log in via console go to the Step '3'

Kind regards,

Sofia Gätjens

[Willgomez845]

I am unable to resolve this issue, also 1 of the jacks have snapped and will not stay connected.  What is the the process to have a technician come out and work on it. 

[Imran_ruckus]

Hi @Willgomez845 

Greetings!!!

Thank you for contacting RUCKUS Lennar Home Community.

I hope you are doing well!!!

Thank you for the response.

Apologies, effective November’2022, ‘Ruckus Support for Lennar Homes customers will no longer be handled by phone or email or remote session. We will be exclusively supporting customers via this community forum support model only.

RUCKUS does not have any support team of technicians to support on-site for Lennar Homes.

However, please do not worry, I will help you get this issue resolved as early as possible.

As per the picture you shared previously, the light status of the RUCKUS ICX-7150-C12P Switch is in a normal state.

We may need to check some configuration and Switch ports information. Please follow the below process and help us with the same.

Please follow the below steps and help us with the queries:

1. To check this issue, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily. 

How to find my Ruckus “Devices IP address” using free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Device...

2. Once we identify the IP address of the switch proceed to access remotely to the device “Command Line” 

How to remotely access to 'ICX 7150-C12P' or 'access points' "Network devices":

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-IC...

If you can access the Command line should look like this:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

Please enter the below commands once you log in to CLI and share the output.

Note: Hit Enter to accept each command 

ICX7150-C12 Switch>enable
ICX7150-C12 Switch#show version

ICX7150-C12 Switch#show flash
ICX7150-C12 Switch#show inline power
ICX7150-C12 Switch#show inline power detail

Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Willgomez845]

As I stated in my previous email one of the jacks snapped and won't lock into the port.  There has to be someone that is available to provide service?