ATT internet doesn't want to cooperate with Ruckus routers anymore.

[Mjxyoit]

Hello, We Bought a new construction Lennar Duplex in 2019. We have two r510 Ruckus units with the firmware updated. Yet, as of a few days ago we get a heartbeat loss every 12 hours like clockwork. This morning, they wouldn't output anything. We thought the internet was out. However, anything using the ATT modem or ether port had internet and everything on Ruckus Wi-fi or ether port was dead. myAT&T app messages said my modem was rejecting the routers. I reset the modem and they work, for now. I booked a service appointment for Monday from ATT. I'm not even sure if ATT will be able to help.

The thing is, I'm reading through the forums and have no idea what is being said. I don't know the lingo. Everything is very cryptic.  I desperately need a resolution. With work and school internet is akin to water in our lives. 

[Imran_ruckus]

Hi @Mjxyoit 

Greetings!!!

Thank you for contacting RUCKUS Lennar Home Community.

Hope you are doing well!!!

Thank you for the detailed information you shared.

As per the case description, I could understand that your RUCKUS setup is not working.

Could you please let us know the answers to the below queries to assist you better?

1. Was there any power outage before you started facing this issue?

2. On your switch while it's plugged into the outlet, do you see any lights on? (Amber or green) Please let us know which lights are on. (Please refer to the below picture and share a picture of the same showing the light status and port connections)

3. Is your Internet Connection from the Internet Service Provider (ISP) stable and working? (You could check this by connecting to your local router Wi-Fi or from an ethernet cable from Router to a laptop/PC)

4. May I know how many Access Points are connected to the Switch? Could you please let me know the light status on the Access Points? Any of these lights are on (Please refer to the below picture and share a picture of the same)

Please help us with pictures of your ICX-7150-C12P Switch showing the status of the lights. Also, light the status of Access Points.

Before uploading the photos please log in to the RUCKUS account and you can upload the image.

Please let us know the answers to the above queries or if you have any queries in this regard.

Thank you again for your patience and understanding

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Mjxyoit]

I am happy to hear from you!!!

The ATT service gentleman left an hour ago. He doesn't know anything about RUCKUS only mentioned that he's visited other houses with similar issues. He tinkered with the internet hub in our master bedroom closet, the transformer outside and, the side of our house. Ran some tests on his phone and got all green checks. He said our speed was slow, but I tested the speed before arrival, there is no difference. 

Answers to the questions below:
1. No power outage within the last few weeks.
2. The "STAT" light is on and is green.
3. Yes, my internet is working and fully operational; especially since ATT just came and verified.
4. I have two access points. The upstairs device (closest to the modem) has 4 green lights on 5G, 2.4G, CTL, PWR. The downstairs device (we have no basement) has 3 green lights on 5G, 2.4G, PWR.

https://postimg.cc/gallery/wMk5JmG
https://postimg.cc/gallery/xdcc3zc
https://postimg.cc/xqjJH1y6

[Imran_ruckus]

Hi @Mjxyoit 

Thank you for the response and the information you shared.

This issue may happen when the Switch runs on the Routing code (SPR). The Switch should run on the Switching code (SPS) to avoid these issues for Lennar home users. If the Switch boots up on the other partition (Due to a power outage/power spike) which may be running on a ‘Routing Code’ results in causing this issue. To check the same please follow the below process.

Please follow the below steps and help us with the queries,

1. To check this issue, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily. 

How to find my Ruckus “Devices IP address” using free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Device...

2. Once we identify the IP address of the switch proceed to access remotely to the device “Command Line” 

How to remotely access to 'ICX 7150-C12P' or 'access points' "Network devices":

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-IC...

If you can access the Command line should look like this:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

Please enter the below commands once you log in to CLI and share the output.

Note: Hit Enter to accept each command 

enable 

show version

show flash

Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again for your patience.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Mjxyoit]

Hello again @ Imran_ruckus

I aspire to say I did what you requested. 
For the record, I'm terrible at this and have no idea what anything means. I will do my best though. Thank you for your continued support.
https://postimg.cc/HrRwDR7T