CommScope RUCKUS Community Forums

mrozone · ‎03-04-2025

After a power outage and a reset we are still getting the following errors

what is our next step?

mrozone · ‎03-06-2025

my config is default. no ip no nothing. I tried to use backup, thats corrupt too. If you take a look at the original posting, is it normal for all volumes to be corrupt?

Imran_ruckus · ‎03-07-2025

Hi @mrozone

Greetings!!!

Thank you for the response and the update.

If you are unable to get the IP address of the Switch, please try getting console access to the Switch and help me with the command outputs I shared previously.

Here is a guide on how to access to the Switch via console (cable access between your PC to the ICX 7150-C12P) in this case, we need a USB type C to USB standard OR Console cable Rj45 to USB (Any one cable- please refer the guide)

How to console in the ICX-7150-C12P

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-console-in-the-ICX-71...

1. Once again, please make sure to download the zip drive for the file below & "extract all". Once it's extracted, run the file, the driver should be installed using the 2 links below.

Link 1: https://support.ruckuswireless.com/software/1414-brocade-ruckus-7150-usb-serial-driver-windows

Link 2: silabs.com/developers/usb-to-uart-bridge-vcp-drivers?tab=downloads

Once installed restart your laptop and try to locate the COM port details under 'Ports (COM & LTP)' with cables connected between the Laptop and the Switch (Refer to the below screenshot), Please check and let me know if that works.

If you have already tried the above process, please share pictures showing the console cable connections between the Switch and the laptop.

Please let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

mrozone · ‎03-07-2025

here you go

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2025.03.07 11:56:20 =~=~=~=~=~=~=~=~=~=~=~=

show version

UNIT 1: compiled on Aug 30 2018 at 04:38:38 labeled as SPS08070c

(25713184 bytes) from Primary

SW: Version 08.0.70cT211

Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225 (mnz10113)

Compiled on Tue Jul 24 10:23:08 2018

HW: Stackable ICX7150-C12-POE

==========================================================================

UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module

Serial #:FEK3811Q08R

Current License: 2X1G

P-ASIC 0: type B160, rev 11 Chip BCM56160_B0

==========================================================================

UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module

==========================================================================

UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module

==========================================================================

1000 MHz ARM processor ARMv7 88 MHz bus

8192 KB boot flash memory

2048 MB code flash memory

1024 MB DRAM

STACKID 1 system uptime is 1 hour(s) 25 minute(s) 59 second(s)

The system started at 00:01:45 GMT+00 Sat Jan 01 2000

The system : started=cold start

ICX7150-C12 Switch#show flash

Stack unit 1:

NAND Type: Micron NAND 2GiB (x 1)

Compressed Pri Code size = 25713184, Version:08.0.70cT211

Compressed Sec Code size = 25713184, Version:08.0.70cT211

Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225

Code Flash Free Space = 1319161856

ICX7150-C12 Switch# shwo ow inf line power

Power Capacity: Total is 124000 mWatts. Current Free is 124000 mWatts.

Power Allocations: Requests Honored 12 times

Port Admin Oper ---Power(mWatts)--- PD Type PD Class Pri Fault/

State State Consumed Allocated Error

--------------------------------------------------------------------------

1/1/1 On Off 0 0 n/a n/a 3 n/a

1/1/2 On Off 0 0 n/a n/a 3 n/a

1/1/3 On Off 0 0 n/a n/a 3 n/a

1/1/4 On Off 0 0 n/a n/a 3 n/a

1/1/5 On Off 0 0 n/a n/a 3 n/a

1/1/6 On Off 0 0 n/a n/a 3 n/a

1/1/7 On Off 0 0 n/a n/a 3 n/a

1/1/8 On Off 0 0 n/a n/a 3 n/a

1/1/9 On Off 0 0 n/a n/a 3 n/a

1/1/10 On Off 0 0 n/a n/a 3 n/a

1/1/11 On Off 0 0 n/a n/a 3 n/a

1/1/12 On Off 0 0 n/a n/a 3 n/a

--------------------------------------------------------------------------

Total 0 0

ICX7150-C12 Switch#show inline power detai

Power Supply Data On unit 1:

++++++++++++++++++

Power Supply Data:

++++++++++++++++++

Power Supply #1:

Max Curr: 2.3 Amps

Voltage: 54.0 Volts

Capacity: 124 Watts

PoePower: 124 Watts

POE Details Info. On Unit 1 :

General PoE Data:

+++++++++++++++++

Firmware

Version

----------------

02.1.0 Build 002

Hardware

Version

----------------

V2R4

Cumulative Port State Data:

+++++++++++++++++++++++++++

#Ports #Ports #Ports #Ports #Ports #Ports #Ports

Admin-On Admin-Off Oper-On Oper-Off Off-Denied Off-No-PD Off-Fault

-------------------------------------------------------------------------

12 0 0 12 0 12 0

Cumulative Port Power Data:

#Ports #Ports #Ports Power Power

Pri: 1 Pri: 2 Pri: 3 Consumption Allocation

-----------------------------------------------

0 0 12 0.000 W 0.000 W

ICX7150-C12 Switch#show interface brief

Port Link State Dupl Speed Trunk Tag Pvid Pri MAC Name

1/1/1 Down None None None None No 1 0 d4c1.9e96.3a84

1/1/2 Down None None None None No 1 0 d4c1.9e96.3a85

1/1/3 Down None None None None No 1 0 d4c1.9e96.3a86

1/1/4 Down None None None None No 1 0 d4c1.9e96.3a87

1/1/5 Down None None None None No 1 0 d4c1.9e96.3a88

1/1/6 Down None None None None No 1 0 d4c1.9e96.3a89

1/1/7 Down None None None None No 1 0 d4c1.9e96.3a8a

1/1/8 Down None None None None No 1 0 d4c1.9e96.3a8b

1/1/9 Down None None None None No 1 0 d4c1.9e96.3a8c

1/1/10 Down None None None None No 1 0 d4c1.9e96.3a8d

1/1/11 Down None None None None No 1 0 d4c1.9e96.3a8e

1/1/12 Down None None None None No 1 0 d4c1.9e96.3a8f

1/2/1 Down None None None None No 1 0 d4c1.9e96.3a91

1/2/2 Down None None None None No 1 0 d4c1.9e96.3a92

1/3/1 Down None None None None No 1 0 d4c1.9e96.3a93

1/3/2 Down None None None None No 1 0 d4c1.9e96.3a94

mgmt1 Down None None None None No None 0 d4c1.9e96.3a84

ICX7150-C12 Switch#

mrozone · ‎03-07-2025

ICX7150-C12 Switch#sh run
Current configuration:
!
ver 08.0.70cT211
!
stack unit 1
module 1 icx7150-c12-poe-port-management-module
module 2 icx7150-2-copper-port-2g-module
module 3 icx7150-2-sfp-plus-port-20g-module
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface ethernet 1/3/1
speed-duplex 1000-full
!
interface ethernet 1/3/2
speed-duplex 1000-full
!
!
!
!
!
!
!
!
!
end

Imran_ruckus · ‎03-07-2025

Hi @mrozone

Greetings!!!
Thank you for the response and the update.

I see your Switch version is on an outdated non-UFI version.

We suggest upgrading your Switch to a stable UFI version.

Please refer to the below RUCKUS Lennar Knowledge Base self-help article for the Upgrade process.

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-upgrade-RUCKUS-ICX-71...

If you can access CLI, We suggest to follow the 2nd option.

Please let me know if you need any help during the upgrade process.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

CommScope RUCKUS Community Forums

7150 corrupt mount error