192.168.0.2 is not alive and Switch in boot mode after power outage

[sonia3187]

Hi,

My power flickered and since then the Switch - ICX 7150 hasn't started. The amber light is on and when I attempt recovery by following the steps suggested in this post - https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-a-Software-re..., I am getting the error as shown in the screenshot below - 

I am using both an Ethernet cable (with RJ45 connectors on both ends) and a USB to Type-C cable, as outlined in steps 2 and 3 of the provided guide. 

My windows firewall is also turned off and I restarted my computer multiple times as well.

Please assist. Thanks!

[Imran_ruckus · Accepted solution]

Hi @sonia3187 ,

I hope this message finds you well.

Thank you for your prompt response and for providing the update.

Upon reviewing one of the images you shared, I noticed that the Ethernet cable on the RUCKUS ICX-7150-C12P switch is currently connected to the incorrect port. It should be plugged into the designated port, as highlighted in the screenshot below. For your reference, please follow steps 2 and 3 outlined in the guide linked previously.

Once the correction is made, I kindly ask that you close the PuTTY session and restart the process. Please then initiate the software recovery process starting from the setenv IP configuration step.

Should you have any further questions or require additional assistance, please don’t hesitate to reach out.

Thank you for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Imran_ruckus · Accepted solution]

Hi @sonia3187 

I hope this message finds you well.

Thank you for your prompt response and the information provided. 

Based on the status of the lights and the cable connections to the RUCKUS ICX-7150-C12P Switch, everything appears to be in normal working order.

At this stage, we recommend performing a factory reset on the Access Points and reconfiguring them with a new Wi-Fi network/SSID. For your convenience, please refer to the following RUCKUS Lennar Knowledge Base article, which outlines the steps for the factory reset process:
Factory Reset Process for RUCKUS R510 Access Points

Should you require any assistance during this process, please do not hesitate to reach out. We are here to support you.

Thank you once again for your patience and understanding.

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

[Imran_ruckus]

Hi @sonia3187 

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

Thank you.

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

[Imran_ruckus]

Hi @sonia3187 

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

If we do not receive a response from you within 24 hours from the timestamp of this message, your case will proceed to closure.

Thank you.

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

[sonia3187]

Thank you for your help!

My Ruckus wi-fi is working absolutely perfect after creating a new Network Id.

[Imran_ruckus]

Hi @sonia3187 

Thank you for the response.

Great!!! Good to know that the issue is now resolved. 

We appreciate your time and patience on this case.

Thank you again for contacting RUCKUS Lennar Home Community and feel free to contact us for future queries.

Have a great day ahead!!!

Did I answer your queries? If yes, hit the Kudos buttons and also accept the answers as Accepted solutions.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Imran_ruckus]

Hi @sonia3187 

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

Thank you.

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community