CommScope RUCKUS Community Forums

rafael_rocha_i5 · 08-30-2021

Hi fellows, my environment in question is about one smartzone 6.0.0.0.1331 and 100 managed icx switches. To the point. I am try to see when a port of the switches goes in the ERR-Disable state due of the bpdu protect acting up. In the smartzone netwo...

rafael_rocha_i5 · 06-23-2021

Hello pack ! I am having trouble in 2 stack of switches that after a reboot by unknown reason somehow "managed" to change their ufi to non-ufi firmware even if they keeped the same version. So the situation is that group of switches of a specific ...

rafael_rocha_i5 · 04-13-2021

Hello, We are installing a group of stack 7150 switches. When In place we saw that a few stacks are having more or less Switches as required. so the problem is when trying to remove the units that will not be necessary the master switch of the stack ...

rafael_rocha_i5 · 11-25-2020

Hello, we have vsmartzone with have two zones with more than 4 groups wlans each. The groups have different numbers of ssid, a few with 11 ssids, others with 9 or 8. My problem is that a specific ssid is been ''removed'' from time to time from my g...

rafael_rocha_i5 · 12-24-2018

I am studying for a public transport scenario and the M510 model look good to me.But in the docs is not clear if mesh and LTE can work together in this model.Lets say that I have a public station, and my transport as it runs its course sometimes can ...

rafael_rocha_i5 · 07-15-2021

Hey Ben, reloading/rebooting the switches stacks did not make the switches coming online to the smartzone and show version still keeping saying that the switch is non-UFI.

rafael_rocha_i5 · 06-23-2021

Hi Ben, thanks for the reply, so, I should reboot the switch or to re-apply by the CLI the firmware again ? It should not be a only "display" problem, as this stacks a are not able to connect tom sz again.

rafael_rocha_i5 · 05-07-2021

Just to update and made sure that other persons will be able to find the answer here. Ben you first instruction was correct. The support told me the same commands as you and it worked for me. To remove a unit from a stack the correct command its to e...

rafael_rocha_i5 · 04-13-2021

Hi Ben, thanks for the input. I am not sure if this command that you suggest is valid for the icx switches, I am not able to find a example in the documentation or the internet. I am tried to follow this suggestions. https://www.youtube.com/watch?v...

rafael_rocha_i5 · 12-02-2020

Hi, the situation was that there was two APs models using the wlan groups that had/have the limit of 16 ssids, each mean that is only 8 different ssids because the 16 count is like SSID test(2.4ghz) + test(5ghz) = 2 ssids. As a suggestion Ruckus cou...

CommScope RUCKUS Community Forums

User Statistics

User Activity

Smartzone - Switch Custom Event/Alarm EER-Disable not triggering ?

Managed ICX 7150 Stack Switches after a reboot change UFI to non-UFI ?

ICX 7150 stack unconfigure unit # not working ? 08.0.90jT211

SSID disappearing from WLANs groups in both zones.

M510 AP - GPS question and Is possible to have Mesh and LTE as a backup wan connection ?

Re: Managed ICX 7150 Stack Switches after a reboot change UFI to non-UFI ?

Re: Managed ICX 7150 Stack Switches after a reboot change UFI to non-UFI ?

Re: ICX 7150 stack unconfigure unit # not working ? 08.0.90jT211

Re: ICX 7150 stack unconfigure unit # not working ? 08.0.90jT211

Re: SSID disappearing from WLANs groups in both zones.