cancel
Showing results for 
Search instead for 
Did you mean: 

SWITCH STILL WONT CONNECT AFTER SEVERAL BOOT SEQUENCE & RELOADING ATTEMPTS

samanthacook176
New Contributor

ICX7150-C12 still boots from partition #2 vs partition #1 AFTER SEVERAL BOOT SEQUENCE & RELOADING ATTEMPTS. Its still showing as a "router" and not a "switch"

I followed these steps in this forum which usually work after every power outage when this happens, but not this time after multiple attempts: https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

My ICX7150-C12 still boots from partition #2 vs partition #1 like its supposed to and is reading as a "router" vs a "switch" like its supposed to.

I have the correct IP address and serial number if needed upon request.

PLEASE HELP TO GET MY SWITCH RECONNECTED

18 REPLIES 18

ready for upgrade instructions

 

Hi 

Thank you for the response and the update.

The recommended stable version is 8095g (08.0.95g)-

Below are the options or methods to perform the Upgrade on the switch: You could choose any one of these.

1st Option:

1. In this option, we will use a pen drive or USB flash drive in which we move the files to the pen drive and connect it to the Switch then through CLI we execute the commands to upgrade the Switch using the following guide as a reference:

How to Upgrade a Switch ICX-7150-C12P using a USB flash drive

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

2nd Option:

2. The following guide is an example of an upgrade via TFTP server, by using an application (FREE) to send files or upload remote files to a device, in our case, we will use it to update a new version to the Switch, basically it will send the image version remotely from the computer to the switch.

How to upgrade a Switch ICX7150-C12P via TFTP

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

3rd Option:

3. In this option we Upgrade the Switch from the Web Interface (GUI) of switch.

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-an-Upgrade-vi...

Try to access your switch from a web browser by pasting the below URL in http or https form whichever that works.

https://0.0.0.0 or http://0.0.0.0 (IP address of Switch. 0.0.0.0 is just as an example)

 

As you can access CLI, I would suggest you follow the 2nd option.

Please let me know if you have any queries in this regard.

Thank you again for your patience.

 

Best regards,

Imran Sanadi

Lennar Home Community.

I used your reccomended option #2

I get stuck here: "

Come back to your Putty APP and start the upgrade by running the next command to upgrade the boot:

“copy tftp flash 10.45.19.152 spz10114.bin bootrom”

I GET THIS OUTPUT AFTER FOLLOWING THE STEPS. IM MAKING SURE THAT THE IP ADRESS MATCHES ON THE TTPDF64 ALL AS WELL PRIOR TO PRESING ENTER

SSH@ICX7150-C12-Switch#copy tftp flash 10.0.0.247 spz10114.bin bootrom
Invalid input -> bootrom
Type ? for a list
SSH@ICX7150-C12-Switch#

 

do u know whats wrong here? I'm messing up the code somehow?

If you type a '?' instead of typing 'bootrom' what options do you get?

Hi @samanthacook176 

Since you are on higher version you dont need to install the 8080f version you can go ahead and install the 8095G firmware version.

You can start from this step:

higher.PNG

From the USB guide it will be from step "20" as reference 

Best Regards 

Fernando Vasquez