cancel
Showing results for 
Search instead for 
Did you mean: 

Ruckus switch not functioning with ATT fiber internet.

karthikv9
New Contributor

I moved into lennar home last year. I had Comcast Xfinity internet last year. It was working well when the router/modem combo (Netgear C7100). I got great internet in all three floors, thanks to the WAPs. I then upgraded my router/modem to Netgear Nighthawk. The internet was not great then.

Later, I moved from Comcast Xfinity to ATT fiber. Now, the ATT fiber internet from it's gateway is great. But, I am not getting great internet when I connect it to the Ruckus switch. The internet is very intermittent. I am not sure if I have to reset the switch or WAPs. Can anyone please guide on what has to be done in this case? 

1 ACCEPTED SOLUTION

Hi @karthikv9

Please run the following commands to solve the issue.

Enable

copy flash flash secondary  ( try many times if it fails  ) 

Boot system flash secondary yes

What this is going to do is copy the SPS image in the secondary flash by re-flashing both images in SPS which will prevent the Switch from having to use 'SPR' routing code.

How to Fix Routing code issues on Lennar Home users

Here is a guide that have a better explanation : 

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

 

Best regards,

Jayavidhya

Lennar Home Community

 

View solution in original post

3 REPLIES 3

Jayavidhya
Moderator
Moderator

Hi @Karthikv9

Please confirm if the issue is happening while it is connected to access points or when it is connected to ISP router. 

Please follow out the next steps.

  1. Connect the computer to the ISP router with the ethernet cable. Run the speed test, and confirm if your speed is stable and search for websites,  make sure you have no issues.
  2. You can perform the same step on wireless by connecting the computer to the Wi-Fi / SSID coming from the ISP router. (Note: Not the Wi-Fi coming from the access points.)
  3. If you have confirmed that internet issue is stable while you are connecting to the ISP router, but the issue persists while you are connecting to the access points or the switch, it looks like your Switch (ICX7150 Switch) may be booting from the secondary partition ( Note: Secondary partition contains the routing code)  which is causing the bad connectivity issues. This could happen after multiple power outages, please follow up the next guide.

How to Fix Routing code issues on Lennar Home users via Web GUI.

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

 How to Fix Routing code issues on Lennar Home users via CLI

Guide#1 for CLI: 

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

Guide#2 for CLI: 

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-solve-the-routing-cod...

Note:  if you have access to the Unleashed Dashboard and the Switch can be seen from there, it may look like the following image, ICX7150-C12-Router instead of ICX7150-C12-Switch, now before starting the steps of the guide, I will advise you to cable the computer directly to the Switch, since you will have a better connectivity than if you connect via wireless. 

  1. After fixing the issue of the Switch booting from the wrong partition, please perform an upgrade to the code 08095g UFI and upgrade both partitions primary and secondary with the switching code file named SPS08095gufi.bin, take into consideration that is the Switch is running a code lower than 08080 you need to upgrade twice, from the code you are to 08080f and then the recommended code 08095g UFI.

How to Upgrade a Switch ICX-7150-C12P using a USB flash drive

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

How to upgrade a Switch ICX7150-C12P via TFTP

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

Upgrade a switch via Web GUI (ICX7150 Switch)

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-an-Upgrade-vi...

Best regards,

Jayavidhya

Lennar Home Community

 

Thank you Jayavidhya. I followed the steps you mentioned and changed the boot sequence to primary flash. However, after the reload, the switch still boots from secondary flash (SPR)

Hi @karthikv9

Please run the following commands to solve the issue.

Enable

copy flash flash secondary  ( try many times if it fails  ) 

Boot system flash secondary yes

What this is going to do is copy the SPS image in the secondary flash by re-flashing both images in SPS which will prevent the Switch from having to use 'SPR' routing code.

How to Fix Routing code issues on Lennar Home users

Here is a guide that have a better explanation : 

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

 

Best regards,

Jayavidhya

Lennar Home Community