Showing results for 
Search instead for 
Did you mean: 

Power outage unleashed network being weird

New Contributor

Power was out 45 mins. The app shows my unleased is online. Problem steaming live stuff and android phone keeps going between Lennar network and 5g. My fios network working fine have reconnected most stuff to that network but I have a 2 story so not the best solution. Please note I AM NOT TECH SAVVY at all. Need a simple easy to carry out solution. Thxs.



Hi @debra_lopes ,


Thank you for contacting RUCKUS Lennar Home Community.

I hope you are doing well!!!

Thank you for the information you shared.

From the case description, I understand that you are facing issues with your Ruckus setup.

Before we can help, we need to check which version the Switch is  currently running.

Please follow the below steps and help us with the queries,

  1. To check this, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily.

How to find the IP Address of the RUCKUS Devices (Switch and APs) using IP Scanner free applications:

2. Once we identify the IP address of the switch proceed to access remotely to the device “Command Line”

If you can access the Command line should look like this:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

Please enter the below commands once you log in to CLI and share the output.

Note: Hit Enter to accept each command


show version

show flash

Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again. We appreciate your patience and understanding.


Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

wouldn't the ip address be what's listed in my unleased app as ap address? It tell me ip address, firmware, mac address ect. It's  model r510  and app is working telling me I'm online? 

telnet@ICX7150-C12 Router>enable
No password has been assigned yet...
telnet@ICX7150-C12 Router#show version
Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
UNIT 1: compiled on Nov 20 2018 at 00:20:22 labeled as SPR08080d
(29819448 bytes) from Secondary SPR08080d.bin
SW: Version 08.0.80dT213
Compressed Boot-Monitor Image size = 786944, Version:10.1.14T225 (mnz10114)
Compiled on Thu Nov 15 12:59:22 2018

HW: Stackable ICX7150-C12-POE
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3812R0K5
Software Package: ICX7150_BASE_L3_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 12 day(s) 6 hour(s) 34 minute(s) 1 second(s)
The system started at 00:10:37 GMT+00 Sat Jan 01 2000

The system : started=cold start

telnet@ICX7150-C12 Router#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 25968884, Version:08.0.80dT211 (SPS08080d.bin)
Compressed Sec Code size = 29819448, Version:08.0.80dT213 (SPR08080d.bin)
Compressed Boot-Monitor Image size = 786944, Version:10.1.14T225
Code Flash Free Space = 1204998144
telnet@ICX7150-C12 Router#^C
telnet@ICX7150-C12 Router#
telnet@ICX7150-C12 Router#telnet@ICX7150-C12 Router>enable
Invalid input -> telnet@ICX7150-C12 Router>enable
Type ? for a list

Hi @debra_lopes ,

Thank you for the response and the information you shared. 

This issue is because your switch is running on the Routing code (SPR). The Switch should run on the Switching code (SPS) to avoid these issues for Lennar home users. Due to a power outage/power spike, the Switch boots up on the other partition which may be running on a ‘Routing Code’ results in causing this issue.

As I can see from the output you shared, your Switch is booted up on the secondary partition which is running on Routing code (SPR) as highlighted in the below screenshot. 

Please follow the below RUCKUS Lennar Knowledge base self-help article which will help you to fix the issue when the Switch is running in the Routing code.

Please follow the process as explained in the article and let me know if you have any queries in this regard. 

We suggest upgrading your switch to the latest stable version to avoid this issue in the future. Your Switch is on an older version that is 08080d. Please let us know once you complete the above process to assist you with the Upgrade of the Switch.

Please let me know if you have any queries in this regard.

NOTE: Please feel free to mark the post as ACCEPTED SOLUTIONS.

Thank you again for your patience and understanding.


Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.