Password Help for Ruckus Network

[galbreath52]

I recently purchased a home with ruckus installed already. Need help accessing (e.g password) ruckus network 

[Jayavidhya]

Hi @galbreath52

Most often the default password for access points and ICX - 7150 - C12 P are

Username:admin password: Ruckus! 

Username:admin password: Ruckus1

Username:admin password: Lennar

Username:super password: sp-admin

Admin usernames and passwords for the Ruckus Wi-Fi Access Points/Switch for Lennar home users

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Admin-usernames-and-password...

 Note : This is sensitive to the keys so it must go with the capital letters indicated

Admin usernames and passwords for the Ruckus Wi-Fi Access Points/Switch for Lennar home users

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Admin-usernames-and-password...

If you want to reset the Access Point ( white box on the ceiling )  Read the following guide carefully, you must disconnect the other access points from the Ruckus Switch by disconnecting the Ethernet cable and only leaving 1 connected in which you are going to work the factory reset.

Physical Factory Reset an Access Points Ruckus

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/Physical-Factory-Reset-an-Ac...

If you want to process a factory reset the ICX-7150-C12P default password is  ( username:super password : sp-admin )

Please try to press the reset button using a paper click or a small stick 

1. Remove power from the switch.
2. Press and hold the Reset button while applying power to the switch.
3. After all the system LEDs flash amber, release the Reset button.

https://docs.commscope.com/bundle/icx7150-installguide/page/GUID-D3B5DB74-53A7-4F8D-82F9-6EB600879EE...

Video link:https://www.youtube.com/watch?v=6jHMTdo_hK4

If that does not work you need to console the ICX-7150-C12P  in order to preform a password recovery using a (  ( ICX 7150 -C12P )  USB type C to USB- ( PC ) cable ) or  ( ( ICX 7150 C12P ) - Rj45 to USB-  ( PC  ) cable )  

Here a short guide : 

How to console in the ICX-7150-C12P

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-console-in-the-ICX-71...

Password recovery 

https://www.youtube.com/watch?v=XJS28DWbHM4&t=94s

1.Start a CLI session over the serial ( console access) interface to the RUCKUS ICX device.

2-Enter OS mode. This uses a key combination and drops below the fastiron operating system

Key Combination: Ctrl+y, release, tap 'm', tap 'Enter'

OS>

4-just write reset

OS>reset

5-.While the system is booting, before the initial system prompt appears,
enter b to enter the boot monitor mode.

Enter 'b' to stop at boot monitor: 0

In this Part you have to press B before the counter ends

6-Enter no password. (You cannot abbreviate this command.)

ICX7650-Boot> no password
00 00 00 00
OK! Skip password check when the system is up.

7-Enter boot. This command causes the device to bypass the system password
check.

ICX7650-Boot> boot

8-After the console prompt reappears, assign a new password.

Best regards,

Jayavidhya

Lennar Home Community

[galbreath52]

This did not work. I cannot ping 192.168.0.01.