cancel
Showing results for 
Search instead for 
Did you mean: 

Internet doesn't work when connected to AP (Lennar Home)

chef_boy_r_G
New Contributor

Hello, 

My internet doesn't work when connected through the ruckus access point I set up. However, it does work when I use the ethernet cable directly from the ICX switch or router. My internet also works connecting directly to my router from the provider. 

All of the lights are green on the ICX switch and I have all ethernet cables plugged into 1 of the 12 ports. 

The lights are all green on the AP as well. 

This worked until I switched providers and I couldn't get it to work again. I'm not sure what changed. 

Thank you

11 REPLIES 11

pinky_ruckus
Moderator
Moderator

Hi @chef_boy_r_G ,

Greetings!

Thank you for contacting RUCKUS Lennar Home Community.

I hope you are doing well!!!

Thank you for the information you shared.

From the case description, I understand that you are facing issues connecting to Internet when connected with AP.

Before we can help, we need to check which version the Switch is  currently running.

Please follow the below steps and help us with the queries,

1.  To check this, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily.

How to find the IP Address of the RUCKUS Devices (Switch and APs) using IP Scanner free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-find-the-IP-Address-o...

2.  Once we identify the IP address of the switch proceed to access remotely to the device “Command Line”

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-access-the-Command-Li...

 

If you can access the Command line should look like this:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

Please enter the below commands once you log in to CLI and share the output.

Note: Hit Enter to accept each command

enable

show version

show flash

Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again. We appreciate your patience and understanding.

 

Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

pinky_ruckus
Moderator
Moderator

Hello @chef_boy_r_G ,

Greetings!

This is a follow-up in reference to the case you have opened in the Ruckus Lennar Support Community.

I would like to know if you require further assistance since our last correspondence. Should you have any questions or if the status of your case has changed, please let me know by responding to this post.

Please feel free to contact if you have any further concerns regarding the same.

 

Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

pinky_ruckus
Moderator
Moderator

Hello @chef_boy_r_G ,

Greetings!

This is a follow-up in reference to the case you have opened in the Ruckus Lennar Support Community.

I would like to know if you require further assistance since our last correspondence. Should you have any questions or if the status of your case has changed, please let me know by responding to this post.

Please feel free to contact if you have any further concerns regarding the same.

 

Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

pinky_ruckus
Moderator
Moderator

Hi @chef_boy_r_G,

Greetings! 

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it. 

If we do not receive a response from you within 24 hours from the timestamp of this message, your case will proceed to closure.

Thank you.

 

Best regards,
Pinky Rajendran

RUCKUS Lennar Home Community