07-19-2023 01:23 PM
No power to APs, dont think we had a power surge but it looks like the most possible circumstance.
Ive tried everything, most tutorials are saying to connect via IP, which I cant because when I scan I dont see the switch on the network even though its connected as always.
When I try and connect via serial, I was able to get into CLI but instead of ICX7150-Router> in the command it says ICX7150-Boot> and doesnt allow commands like enable, show inline power, etc. Just allows me to do things like printenv and whatnot.
Tried setting up TCPT server or whatever and cant get it to connect. Heard it was because i needed to factory reset first, and I did the thing where I hold down the reset when plugging in power so it blinks all amber, but it now just blinks amber indefinitely (its been over an hour). Also the Putty says the following while doing that:
Booted from partition 2
DRAM: Validate Shmoo parameters stored in flash ..... OK
ICX7150-12 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0xa
device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
device 0 offset 0x0, size 0xc0000
bootdelay: ===
Booting image from Primary
NAND read: device 0 offset 0x0, size 0x2000000
8 ecc_errors after reading 18b8000:18b9c00
iproc_nand_read_page returned 2
NAND read from offset 0 failed -22
0 bytes read: ERROR
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
could not boot from primary, no valid image; trying to boot from secondary
device 0 offset 0x0, size 0xc0000
BOOTING image from Secondary
NAND read: device 0 offset 0x4000000, size 0x2000000
8 ecc_errors after reading 58b8000:58b9c00
iproc_nand_read_page returned 2
NAND read from offset 4000000 failed -22
0 bytes read: ERROR
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
For the love of god, help or send me a new one or a technician who can help!
07-24-2023 08:20 AM
Hi @AdventC
Greetings!!!
Thank you for the response and the update.
When we do it with cable console access to the Switch and reset, it should work. Not sure what is wrong.
May I please know if you performed the same using Telnet as well?
Also please reset with some new credentials (new username and password) and check. Please share the screenshots of the same.
Please check, confirm, and let me know if you have any queries in this regard.
Thank you again for your patience and understanding.
Best regards,
Imran Sanadi
RUCKUS Lennar Home Community.
07-24-2023 09:58 AM
Im not sure, I followed the instructions to the letter. Can you share what responses you get if you run that code? I get the same thing every time I do it. I also changed it to different credentials than "super" and "pass" to see if that works and nothing. I didnt try this via telnet.
I do want to add that resetting the switch via OS seems to have fixed my issues with the ethernet. I am at the point where I dont want to touch the switch because everything is finally working again... but it feels like it is a rickety old bridge about to collapse.
07-24-2023 10:24 AM
Hi @AdventC
Thank you for the response and the information.
CLI output should be the same as you sent apart from the ‘Key already exist. Please zeroize it’ error which should not appear after the command ‘crypto key zeroize rsa’
And good to know that you have a stable connection at this point.
To confirm all the configuration once, please share the pictures of the Switch showing the cable connections and the Access Points pictures as well. And please share the screenshots of the Unleashed web system showing the Access Points and Switch connectivity.
Also please share the output of the below commands.
Please enter the below commands once you log in to CLI and share the output.
Note: Hit Enter to accept each command
enable
show version
show flash
show inline power
show interface brief
show inline power detail
Please let me know if you have any queries in this regard.
Thank you again for your patience and understanding.
Best regards,
Imran Sanadi
RUCKUS Lennar Home Community.
07-21-2023 10:04 AM - edited 07-21-2023 10:06 AM
deleting duplicate post