07-19-2023 01:23 PM
No power to APs, dont think we had a power surge but it looks like the most possible circumstance.
Ive tried everything, most tutorials are saying to connect via IP, which I cant because when I scan I dont see the switch on the network even though its connected as always.
When I try and connect via serial, I was able to get into CLI but instead of ICX7150-Router> in the command it says ICX7150-Boot> and doesnt allow commands like enable, show inline power, etc. Just allows me to do things like printenv and whatnot.
Tried setting up TCPT server or whatever and cant get it to connect. Heard it was because i needed to factory reset first, and I did the thing where I hold down the reset when plugging in power so it blinks all amber, but it now just blinks amber indefinitely (its been over an hour). Also the Putty says the following while doing that:
Booted from partition 2
DRAM: Validate Shmoo parameters stored in flash ..... OK
ICX7150-12 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0xa
device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
device 0 offset 0x0, size 0xc0000
bootdelay: ===
Booting image from Primary
NAND read: device 0 offset 0x0, size 0x2000000
8 ecc_errors after reading 18b8000:18b9c00
iproc_nand_read_page returned 2
NAND read from offset 0 failed -22
0 bytes read: ERROR
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
could not boot from primary, no valid image; trying to boot from secondary
device 0 offset 0x0, size 0xc0000
BOOTING image from Secondary
NAND read: device 0 offset 0x4000000, size 0x2000000
8 ecc_errors after reading 58b8000:58b9c00
iproc_nand_read_page returned 2
NAND read from offset 4000000 failed -22
0 bytes read: ERROR
## Loading kernel from FIT Image at 70000200 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
For the love of god, help or send me a new one or a technician who can help!
07-21-2023 10:24 AM - edited 07-21-2023 10:24 AM
Hi Imran,
The documentation you shared says "ICX devices will be automatically discovered by the Unleashed Master. If automatic switch approval is enabled, all ICX switches discovered on the network will be listed in the Switches dashboard component. To disable automatic approval, go to Admin & Services > System > System Info > Switch Approval and disable the Approval option."
Sorry a bit confused because your post says to enable and reboot. My approval box was already enabled when i just checked. Also, I did already try those commands via telnet but couldnt get it to actually change the username and pw. I still cannot login and I tried those commands yesterday.
What should I do?
07-21-2023 10:55 AM
Hi @AdventC
Thank you for the response and the information.
If Switch approval is set to enabled already.
Please try to reset your username and password once again as described in my previous post. And please note it will take some time to sync.
Please share the screenshots of the credentials reset commands you performed.
Please let me know if you have any queries in this regard.
Thank you again for your patience and understanding.
Best regards,
Imran Sanadi
RUCKUS Lennar Home Community.
07-21-2023 11:01 AM
Hi Imran,
It has been over 24 hours since I tried this yesterday. I tried it again just now, please see below:
telnet@ICX7150-C12-Switch>enable
No password has been assigned yet...
telnet@ICX7150-C12-Switch#configure terminal
telnet@ICX7150-C12-Switch(config)#username super password pass
telnet@ICX7150-C12-Switch(config)#crypto key generate rsa
Key already exists. Please zeroize it.
telnet@ICX7150-C12-Switch(config)#aaa authentication login default local
If it isnt supposed to take longer than 24 hours, I think I need another solution. Also, will fixing this fix my Ethernet problem?
07-21-2023 11:17 AM - edited 07-21-2023 11:18 AM
deleting another duplicate post
07-21-2023 12:19 PM
Hi @AdventC
Thank you for the response and the information you shared.
The only option now to reset the Switch credentials is by getting console access as described below.
Here are the short guides and step-by-step process.
How to console in the ICX-7150-C12P:
Short Guide for password recovery:
Video link as a reference: https://www.youtube.com/watch?v=XJS28DWbHM4
1. Start a CLI session over the serial (console access) interface to the RUCKUS ICX device.
2. Enter OS mode. This uses a key combination and drops below the Fastron operating system
Key Combination: Ctrl+y, release, tap 'm', tap 'Enter'
OS>
3. Just write reset
OS>reset
4. While the system is booting, before the initial system prompt appears,
enter b to enter the boot monitor mode.
Enter 'b' to stop at boot monitor: 0
In this part, you have to press B before the counter ends
5. Enter no password. (You cannot abbreviate this command.)
ICX7650-Boot> no password
00 00 00 00
OK! Skip password check when the system is up.
6. Enter boot. This command causes the device to bypass the system password
check.
ICX7650-Boot> boot
7. After the console prompt reappears, assign a new password.
Reset your new credentials as mentioned in the steps below:
Edit the current or create a new password and username by using the below commands:
enable
configure terminal
device(config)# username super password pass
Where the username is ’super’ and password ‘pass’
In order to allow the correct authentication please run the following commands:
Device(config)#crypto key generate rsa
device(config)# aaa authentication login default local
Now you could try using your new credentials to log in on CLI. (If new credentials do not work, please wait for some time and try again later)
Please let me know if you have any queries in this regard.
Thank you again for your patience and understanding.
Best regards,
Imran Sanadi
RUCKUS Lennar Home Community.