Ruckus 5G

[dtsteinb]

I have my laptop connected to my Ruckus and when I do a speed test I can't break 100mbps and I am on a 200mbps line.  If I use the modem Xfinity sent and connect to that 5G I get the 200mbps.  Is this ruckus not capable of real 5G speeds or do I need to configure something?

[dtsteinb]

When I try to login via ssh or web the username / password dont work.  I went through all the combos you gave and NONE worked.  

[Imran_ruckus]

Hi @dtsteinb 

I hope this message finds you well.

Thank you for your update.

Before we address the web login issues, I recommend upgrading your RUCKUS ICX-7150-C12P switch to a supported version. Based on the information you provided, it appears that your switch is currently running an outdated non-UFI SPS08070b version.

For detailed instructions on how to upgrade your RUCKUS ICX-7150-C12P switch, please refer to the following RUCKUS Lennar Knowledge Base article:

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-upgrade-RUCKUS-ICX-71...

If you encounter any difficulties or require assistance during the upgrade process, please do not hesitate to reach out.

Thank you for your patience and understanding.

Best regards,

Imran Sanadi  
RUCKUS Lennar Home Community

[dtsteinb]

This is my 2nd attempt to post the reply.  Here is the output you need

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2024.08.14 17:39:16 =~=~=~=~=~=~=~=~=~=~=~=

telnet@ICX7150-C12-Switch>enalb  ble

No password has been assigned yet...

telnet@ICX7150-C12-Switch#show version

  Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.

    UNIT 1: compiled on Apr  3 2018 at 15:27:41 labeled as SPS08070b

      (25605164 bytes) from Primary SPS08070b.bin

        SW: Version 08.0.70bT211 

      Compressed Boot-Monitor Image size = 786944, Version:10.1.11T225 (mnz10111)

       Compiled on Wed Dec 13 11:13:34 2017

  HW: Stackable ICX7150-C12-POE

==========================================================================

UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module

      Serial  #:FEK3845P2YG

      Current License: 2X1G  

      P-ASIC  0: type B160, rev 11  Chip BCM56160_B0

==========================================================================

UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module

==========================================================================

UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module

==========================================================================

 1000 MHz ARM processor ARMv7 88 MHz bus

 8192 KB boot flash memory

 2048 MB code flash memory

 1024 MB DRAM

STACKID 1  system uptime is 10 day(s) 7 hour(s) 31 minute(s) 27 second(s) 

--More--, next page: Space, next line: Return key, quit: Control-c                                                                  The system started at 00:04:53 GMT+00 Sat Jan 01 2000

The system : started=cold start   

telnet@ICX7150-C12-Switch#show flash

Stack unit 1:

  NAND Type: Micron NAND 2GiB (x 1)

  Compressed Pri Code size = 25605164, Version:08.0.70bT211 (SPS08070b.bin)

  Compressed Sec Code size = 29341752, Version:08.0.70bT213 (SPR08070b.bin)

  Compressed Boot-Monitor Image size = 786944, Version:10.1.11T225

  Code Flash Free Space = 1319120896

telnet@ICX7150-C12-Switch#show inline power

Power Capacity:    Total is 124000 mWatts. Current Free is 86200 mWatts.

Power Allocations: Requests Honored 10 times

 Port Admin Oper    ---Power(mWatts)---  PD Type  PD Class  Pri  Fault/

      State State   Consumed  Allocated                          Error

--------------------------------------------------------------------------

  1/1/1 On On          3400      15400  802.3af  Class 3     3  n/a

  1/1/2 On On          3200      15400  802.3af  Class 3     3  n/a

  1/1/3 On On          2300       7000  802.3af  Class 2     3  n/a

  1/1/4 On Off            0          0  n/a      n/a         3  n/a

  1/1/5 On Non-PD         0          0  n/a      n/a         3  n/a

  1/1/6 On Off            0          0  n/a      n/a         3  n/a

  1/1/7 On Off            0          0  n/a      n/a         3  n/a

  1/1/8 On Non-PD         0          0  n/a      n/a         3  n/a

  1/1/9 On Off            0          0  n/a      n/a         3  n/a

 1/1/10 On Non-PD         0          0  n/a      n/a         3  n/a

 1/1/11 On Non-PD         0          0  n/a      n/a         3  n/a

 1/1/12 On Non-PD         0          0  n/a      n/a         3  n/a

--------------------------------------------------------------------------

 Total                   8900      37800

--More--, next page: Space, next line: Return key, quit: Control-c                                                                  

telnet@ICX7150-C12-Switch#show inline power detail

Power Supply Data On unit 1:

++++++++++++++++++

Power Supply Data:

++++++++++++++++++

Power Supply #1:

Max Curr:  2.3 Amps

Voltage:    54.0 Volts

Capacity:  124 Watts

PoePower:  124 Watts

POE Details Info. On Unit 1 : 

General PoE Data:

+++++++++++++++++

--More--, next page: Space, next line: Return key, quit: Control-c                                                                  Firmware

Version

----------------

02.1.0 Build 002

Hardware

Version

----------------

V2R4

Cumulative Port State Data:

+++++++++++++++++++++++++++

#Ports    #Ports     #Ports   #Ports    #Ports       #Ports     #Ports

Admin-On  Admin-Off  Oper-On  Oper-Off  Off-Denied   Off-No-PD  Off-Fault

-------------------------------------------------------------------------

12        0          3        9         0            4          0        

Cumulative Port Power Data:

--More--, next page: Space, next line: Return key, quit: Control-c                                                                  +++++++++++++++++++++++++++

#Ports  #Ports  #Ports        Power       Power

Pri: 1  Pri: 2  Pri: 3  Consumption  Allocation

-----------------------------------------------

0       0       12          8.900 W    37.800 W

telnet@ICX7150-C12-Switch#  show interface f brief

Port       Link    State   Dupl Speed Trunk Tag Pvid Pri MAC             Name

1/1/1      Up      Forward Full 1G    None  No  1    0   d4c1.9e87.9ce2                 

1/1/2      Up      Forward Full 1G    None  No  1    0   d4c1.9e87.9ce3                 

1/1/3      Up      Forward Full 1G    None  No  1    0   d4c1.9e87.9ce4                 

1/1/4      Down    None    None None  None  No  1    0   d4c1.9e87.9ce5                 

1/1/5      Up      Forward Full 100M  None  No  1    0   d4c1.9e87.9ce6                 

1/1/6      Down    None    None None  None  No  1    0   d4c1.9e87.9ce7                 

1/1/7      Down    None    None None  None  No  1    0   d4c1.9e87.9ce8                 

1/1/8      Up      Forward Full 100M  None  No  1    0   d4c1.9e87.9ce9                 

1/1/9      Down    None    None None  None  No  1    0   d4c1.9e87.9cea                 

1/1/10     Up      Forward Full 100M  None  No  1    0   d4c1.9e87.9ceb                 

1/1/11     Up      Forward Full 100M  None  No  1    0   d4c1.9e87.9cec                 

1/1/12     Up      Forward Full 100M  None  No  1    0   d4c1.9e87.9ced                 

1/2/1      Down    None    None None  None  No  1    0   d4c1.9e87.9cef                 

1/2/2      Down    None    None None  None  No  1    0   d4c1.9e87.9cf0                 

1/3/1      Down    None    None None  None  No  1    0   d4c1.9e87.9cf1                 

1/3/2      Down    None    None None  None  No  1    0   d4c1.9e87.9cf2                 

mgmt1      Down    None    None None  None  No  None 0   d4c1.9e87.9ce2                 

telnet@ICX7150-C12-Switch#show ip address

        IP Address       Type      Lease Time 

        10.0.0.246       Dynamic  567161

telnet@ICX7150-C12-Switch#logout

[Imran_ruckus]

Hi @dtsteinb 

Greetings!!!

I hope this message finds you well.

Thank you for your update.

As I motioned in my previous post, before we address the web login issues, I recommend upgrading your RUCKUS ICX-7150-C12P switch to a supported version. Based on the information you provided, it appears that your switch is currently running an outdated non-UFI SPS08070b version (please refer to the below screenshot).

For detailed instructions on how to upgrade your RUCKUS ICX-7150-C12P switch, please refer to the following RUCKUS Lennar Knowledge Base article:

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-upgrade-RUCKUS-ICX-71...

If you encounter any difficulties or require assistance during the upgrade process, please do not hesitate to reach out.

Thank you for your patience and understanding.

Best regards,

Imran Sanadi  
RUCKUS Lennar Home Community

[dtsteinb]

Looks like this bricked the AP's   I did the boot system flash secondary yes and got disconnected and neither AP has lights