cancel
Showing results for 
Search instead for 
Did you mean: 

Router slow

anonymous13
New Contributor

We recently had a storm here in California. I'm not sure if it's related, but my internet was going very slowly after that. I called AT&T and they suggested I switch to one of their routers, and I did and my internet is working fine now, but I have most of my home devices (Alexa, Ring, etc) connected to my old WiFi network using the Ruckus router. So I'd like to switch back, but I need assistance in re-connecting to it and seeing what the issue is so we can fix it. I'm not sure what version/model of the router it is and I don't know how to check that. 

2 REPLIES 2

Imran_ruckus
Moderator
Moderator

Hi  anonymous13

Thank you for contacting Lennar Home Community.

Hope you are doing well!!!

Thank you for the information you shared,

As per the case description, I could understand that your RUCKUS ICX-7150-C12P Switch is slow after a recent storm.

If there was a blackout or power outage and the switch gets rebooted because of that, most possible your switch starts running the wrong code which we call ‘routing code’ this is a known issue for Lennar home users.

 

Imran_ruckus_0-1675462062043.png

An identifier of this problem is that it comes out as Switch-Router in the unleashed dashboard.

There we are going to see 2 important things the

-MAC address: Physical address of the device this never changes

- An IP address is a unique address (logical) that identifies a device on the internet or a local network like your home (this can change and may not be the same as the one shown on the dashboard)

Please follow the below steps:

  1. To fix this issue, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily. 

How to find my Ruckus “Devices IP address” using free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Device...

  1. Once we identify the IP address of the switch proceed to access remotely to the device “Command Line” 

How to remotely access to 'ICX 7150-C12P' or 'access points' "Network devices":

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-IC...

If you can access the Command line should look like this:

ICX7150-C12 Router>

  1. Here is a quick guide for understanding how to fix the 'routing code issue' however, you only need to run the following commands once you are on the command line 'CLI' 

Note: Hit Enter to accept each command

enable

copy flash flash secondary 

boot system flash secondary yes 

Example: 

VIDEO LINK AS REFERENCE: https://www.youtube.com/watch?v=Eem1IBgYaWc

ICX7150-24P Router>enable (hit enter to accept the command)
ICX7150-24P Router#copy flash flash secondary (hit enter to accept the command and wait: until the flash finished)
ICX7150-24P Router#boot system flash secondary yes (hit enter to accept the command: the switch will reboot)

 

There are Two ways to fix this issue:

         I) How to Fix Routing code issues on Lennar Home users via CLI

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-solve-the-routing-cod...

         II) Or WEB access option

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

 

  1. If access via IP address is not possible here is a guide on how to access to the Switch via console (cable access between your PC to the ICX 7150-C12P) in this case we need a USB type C to USB standard or Console cable Rj45 to USB. 

How to console in the ICX-7150-C12P

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-console-in-the-ICX-71...

Once you are logged in to the ICX-7150-C12P please follow up the same steps that are on point '3'

 

Please let me know if you have any queries in this regard.

Best regards,

Imran Sanadi

Lennar Home Community.

I have reviewed all the post I could find on the issue of slow or throttled speeds. I can not find a fix for my issue. The switch is setting upload/download speeds to @300 mps even when direct connected to the switch with a laptop computer. I have completed software updates, but that seems to be to the APs and completed the flash actions no help. 

tack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 28660224, Version:08.0.90dT211 (SPS08090d.bin)
Compressed Sec Code size = 28660224, Version:08.0.90dT211 (SPS08090d.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.15T225 (mnz10115)
Compressed Sec Boot Code size = 786944, Version:10.1.15T225 (mnz10115)
Code Flash Free Space = 1134657536

I have read at one point this was determined to be a bad switch. 

Any help here pleas?