cancel
Showing results for 
Search instead for 
Did you mean: 

Looking for Dashboard URL link

rajivnandra
New Contributor

I need to access the URL to make the required configuration changes hence please provide the URL.

Regards/Rajiv

 

1 ACCEPTED SOLUTION

Hello @rajivnandra ,

Thank you for the response.

Really apologize for the confusion.

You may directly upgrade it to the 200.15.6.212.14 through the online upgrade option.

Please follow the below RUCKUS Lennar Knowledge base self-help article which will help you to upgrade the Ruckus AP to a recommended version

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/Upgrade-process-of-the-RUCKU...

Please check and let me know if you have any queries in this regard. 

Thank you again for your patience and understanding.

 

Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

View solution in original post

38 REPLIES 38

Currently travelling and will update you end of next week.

Regards/Rajiv

Hi @rajivnandra 

Thank you for your response.

As this case has been pending for an extended period, we are unable to keep it open any longer. Therefore, we will be closing it at this time.

Should you require further assistance in the future, please feel free to open a new post adding this post's link as a reference.

Thank you again for your understanding.

 

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

Hi @rajivnandra 

I hope this message finds you well.

Thank you for your prompt response and the update provided.

If IP Passthrough has been enabled, kindly disable it. This feature assigns a public IP address to one of your devices, which can then be accessed from anywhere on the internet.

Once disabled, please confirm if the heartbeat loss issue persists with your RUCKUS Unleashed Access Points.

Thank you once again for your patience and understanding.

 

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

Hi Pinky,

Below is more information about my ICX7150-C12-POE switch -

telnet@ICX7150-C12 Switch#show version
Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
UNIT 1: compiled on Aug 30 2018 at 04:38:38 labeled as SPS08070c
(25713184 bytes) from Primary
SW: Version 08.0.70cT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225 (mnz10113)
Compiled on Tue Jul 24 10:23:08 2018

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3810Q2T1
Current License:
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 1 day(s) 16 hour(s) 31 minute(s) 31 second(s)
The system started at 00:02:17 GMT+00 Sat Jan 01 2000

The system : started=cold start

telnet@ICX7150-C12 Switch#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 25713184, Version:08.0.70cT211
Compressed Sec Code size = 29437672, Version:08.0.70cT213
Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225
Code Flash Free Space = 1319174144

As per the information I have read the latest firmware version is 08.0.95p.

Q1. Is this correct? If not, then what is the latest firmware version, as I read somewhere it's 08.0.95n as well 09.0.10j_cd5...I am now confused about which version I should pick at present my fiber speed is 2Gig.

Q2. What is the default user id and password from GUI interface?

Q3. Firmware upgrade steps preferably from GUI interface?

Regards/Rajiv