Looking for Dashboard URL link

[rajivnandra]

I need to access the URL to make the required configuration changes hence please provide the URL.

Regards/Rajiv

[rajivnandra]

Here is show flash output -

telnet@ICX7150-C12 Switch#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Pri Code Flash Empty
Sec Code Flash Empty
Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225
Code Flash Free Space = 1374793728
telnet@ICX7150-C12 Switch#

Not sure why I am still getting an error stating "Status : TFTP out of buffer space error."? 

Below is the content from web interface  

TFTP ConfigurationTFTP Server IP:Configuration File Name:

Status : TFTP out of buffer space error.

[Home][Site Map][Logout][Save][Frame Enable|Disable][TELNET]

[rajivnandra]

I am worried as both primary and secondary flash are empty and now what if my switch reboots due to power failure or for any other reason? Can I change the Boot sequence to the "TFTP Server" till we figure out a solution? Please help!! 

[Imran_ruckus]

Hi @rajivnandra 

I hope this message finds you well.

Could you kindly clarify the reason for erasing the primary and secondary components? This action was not suggested or recommended by us.

As previously mentioned, we advised using the Option 2 CLI method for the upgrade process. Proceed with the same.

Thank you again.

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

[rajivnandra]

Hi Pinky,

Below is more information about my ICX7150-C12-POE switch -

telnet@ICX7150-C12 Switch#show version
Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
UNIT 1: compiled on Aug 30 2018 at 04:38:38 labeled as SPS08070c
(25713184 bytes) from Primary
SW: Version 08.0.70cT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225 (mnz10113)
Compiled on Tue Jul 24 10:23:08 2018

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3810Q2T1
Current License:
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 1 day(s) 16 hour(s) 31 minute(s) 31 second(s)
The system started at 00:02:17 GMT+00 Sat Jan 01 2000

The system : started=cold start

telnet@ICX7150-C12 Switch#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 25713184, Version:08.0.70cT211
Compressed Sec Code size = 29437672, Version:08.0.70cT213
Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225
Code Flash Free Space = 1319174144

As per the information I have read the latest firmware version is 08.0.95p.

Q1. Is this correct? If not, then what is the latest firmware version, as I read somewhere it's 08.0.95n as well 09.0.10j_cd5...I am now confused about which version I should pick at present my fiber speed is 2Gig.

Q2. What is the default user id and password from GUI interface?

Q3. Firmware upgrade steps preferably from GUI interface?

Regards/Rajiv