Hi. I bought a Lennar home and it came pre-installed with Ruckus r510 and ICX 7150 C12P. I'm getting around 100 Mbps from speed tests while on the r510. However, on my Asus, I'm pulling around 580 Mbps. I believe the issue is that I'm uplinked from the r510 to the ICX at 100 Full. I can't seem to change the NIC port speeds on my r510 to 1000 Mbps Full. Below are the CLI output from the r510 and ICX. The r510 is connected to port 1/1/1. Port 1/1/3 is uplink to my AT&T modem. I'm running 220.127.116.11.312 on the r510.
telnet@ICX7150-C12 Switch#sh int brief
Port Link State Dupl Speed Trunk Tag Pvid Pri MAC Name 1/1/1 Up Forward Full 100M None No 1 0 c0c5.2093.a943 1/1/2 Down None None None None No 1 0 c0c5.2093.a944 1/1/3 Up Forward Full 1G None No 1 0 c0c5.2093.a945 1/1/4 Down None None None None No 1 0 c0c5.2093.a946 1/1/5 Up Forward Full 100M None No 1 0 c0c5.2093.a947 1/1/6 Down None None None None No 1 0 c0c5.2093.a948 1/1/7 Down None None None None No 1 0 c0c5.2093.a949 1/1/8 Up Forward Full 100M None No 1 0 c0c5.2093.a94a 1/1/9 Up Forward Full 100M None No 1 0 c0c5.2093.a94b 1/1/10 Up Forward Full 100M None No 1 0 c0c5.2093.a94c 1/1/11 Down None None None None No 1 0 c0c5.2093.a94d 1/1/12 Down None None None None No 1 0 c0c5.2093.a94e 1/2/1 Down None None None None No 1 0 c0c5.2093.a950 1/2/2 Down None None None None No 1 0 c0c5.2093.a951 1/3/1 Down None None None None No 1 0 c0c5.2093.a952 1/3/2 Down None None None None No 1 0 c0c5.2093.a953 mgmt1 Down None None None None No None 0 c0c5.2093.a943
ruckus> en ruckus# show config Protocol Mode= IPv4-Only Device IP Address: Mode= DHCP IP Address= 192.168.1.70 Netmask= 255.255.255.0 Gateway Address= 192.168.1.254 Primary DNS= 192.168.1.254 Secondary DNS=
Administrator Name/Password: Name= admin Password= Authenticate: Mode= Authenticate using the admin name and password
AP: ID: 1: MAC Address= 1c:3a:60:36:ae:d0 Model= r510 Approved= Yes Device Name= RuckusAP Device Role= Master Description= Location= GPS= CERT = Normal Bonjour-policy= Bonjour-fencing= Group Name= System Default Channel Range: A/N= 36,40,44,48,149,153,157,161 (Disallowed= ) B/G/N= 1,2,3,4,5,6,7,8,9,10,11 (Disallowed= ) Radio a/n: Channelization= Auto Channel= Auto WLAN Services enabled= Yes Tx. Power= Auto WLAN Group Name= Default Call Admission Control= OFF Protection Mode= Auto Radio b/g/n: Channelization= Auto Channel= Auto WLAN Services enabled= Yes Tx. Power= Auto WLAN Group Name= Default Call Admission Control= OFF Protection Mode= 2 Override global ap-model port configuration= No Network Setting: Protocol mode= IPv4-Only Device IP Settings= DHCP IP Address= 192.168.1.70 Netmask= 255.255.255.0 Gateway= 0.0.0.0 Primary DNS Server= 192.168.1.254 Secondary DNS Server= Mesh: Status= Disabled LLDP: Status = Use Parent Setting LAN Port: 0: Interface= eth0 Dot1x= None LogicalLink= Up PhysicalLink= Up 100Mbps full Label= 10/100/1000 PoE Port1 1: Interface= eth1 Dot1x= None LogicalLink= Down PhysicalLink= Down Label= 10/100/1000 Port2 PoE Mode= Auto
Have you tried updating the firmware on the ICX switch? Yeah leave the ruckus r510 at it’s current firmware since 200.7.x has speed issues with iOS devices. Also, have you tried connecting the r510 to a different port on the switch?
I can confirm that you don’t need an ac adapter ... it’s more likely you have a defective r510. .. the last thing I would try would be reset the r510 to factory settings and reconfigure it. Note you should have a limited lifetime warranty on your unit. Contact ruckus support or Lennar ruckus that it seems that you might have a bad unit.
The other possibility is that termination ends of the cable could be bad? Try taking down the r510 and plugging it directly to the switch with a known good cat5e cable or cat6. Note the r510 is locked down and to release the latch there is a paper clip hole at the front of the base of the unit. Push a paper clip in and you should feel a spring mechanism and the unit backwards and down.