I have an ICX 7150-C12P and the PoE has switched off.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-04-2019 06:33 PM
I have an ICX 7150-C12P. The power was out for several hours and when it came back on the PoE wasn't active. I have done the factory reset about a dozen times and I can't get it back. I've read all these complex instructions on finding IP address, using a terminal prompt etc etc etc. Unfortunately all of that is over my head. Is there a way to manually turn it back on? Any help is greatly appreciated.
53 REPLIES 53
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-29-2019 11:15 AM
Understood. I appreciate your insight and help.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-29-2019 11:08 AM
LOL, it says asset doesn't exist.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-29-2019 11:10 AM
Geez.
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-29-2019 11:14 AM
Geo,
Here is where to get the serial:
show version
SSH@SWITCHNAME#sh ver
Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
UNIT 1: compiled on Oct 11 2018 at 14:00:37 labeled as SPR08080ca
(29823132 bytes) from Secondary SPR08080ca.bin
SW: Version 08.0.80caT213
Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225 (mnz10113)
Compiled on Tue Jul 24 06:23:08 2018
HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:ABC1234D0EF (I changed this, so it isn't a real serial number)
Software Package: ICX7150_L3_SOFT_PACKAGE
Current License: 2X10GR
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 36 day(s) 11 hour(s) 11 minute(s) 1 second(s)
The system started at 02:17:11 Eastern Thu Feb 21 2019
Here is where to get the serial:
show version
SSH@SWITCHNAME#sh ver
Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
UNIT 1: compiled on Oct 11 2018 at 14:00:37 labeled as SPR08080ca
(29823132 bytes) from Secondary SPR08080ca.bin
SW: Version 08.0.80caT213
Compressed Boot-Monitor Image size = 786944, Version:10.1.13T225 (mnz10113)
Compiled on Tue Jul 24 06:23:08 2018
HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:ABC1234D0EF (I changed this, so it isn't a real serial number)
Software Package: ICX7150_L3_SOFT_PACKAGE
Current License: 2X10GR
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 36 day(s) 11 hour(s) 11 minute(s) 1 second(s)
The system started at 02:17:11 Eastern Thu Feb 21 2019
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-29-2019 11:14 AM
NetWizz, The installer, Amazon, didn't leave the cable that is shipped with the unit. I bought a USB to USB-C cable. I'm not sure what crashed the computer, it worked just fine, but the timeline was turned computer on, download Putty, conference with Ruckus tech, connect to switch, crash. This was several weeks ago. I have been able to get the computer to boot a few times and removed Putty and all junk programs, cleaned everything I could, restarted at least 50 times. It's unstable and I need to reload Windows.
