Solved: RUCKUS Forums - Re: How to do Ruckus ICX 7150-C12P Switch health c... - Page 2

Kevin4 · ‎04-18-2025

I am recovering network in Lennar Homes home. Here is what I have with 7150-C12P Switch: can login via console USB connector and run few 'show' commands. Seems that switch can supplie power to access points (4 of them through the house). However, no activity LEDs on RJ45 ports. Cables tested/replaced. Router ports tested and found working well. Access Points working when powered via injectors and connected to small router's hub/switch.

Question - how to verify that 7150-C12P Switch receives signal and transfers signal to network ports using terminal session CLI?

Thank you!

pinky_ruckus · ‎04-18-2025

Hello @Kevin4 ,

Greetings!

Thank you for contacting RUCKUS Lennar Home Community.

I hope you are doing well!!!

Thank you for the information you shared.

From the case description, I understand that you are looking to verify that the ICX-7150 Switch receives signal through ports through CLI.

To check this, we must identify the ‘current’ IP address assigned by your local router to the switch ICX-7150-C12P

I will leave you a guide on how to perform an IP scanner on your local network to identify the switch IP address very easily.

How to find the IP Address of the RUCKUS Devices (Switch and APs) using IP Scanner free applications:

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-find-the-IP-Address-o...

Once we identify the IP address of the switch proceed to access remotely to the device “Command Line”

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-access-the-Command-Li...

If you can access the Command line should look like this:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

Once you login to CLI, please enter the below commands and share the output.

Note: Hit Enter to accept each command

enable

show version

show flash

show inline power

If the highlighted portion is shown as ON, it means that the consecutive ports are getting signal and if OFF, the ports are not getting signal from the Switch.

Please share the output of the above commands or share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

View solution in original post

pinky_ruckus · ‎04-25-2025

Hello @Kevin4 ,

Greetings!

This is a follow-up in reference to the case you have opened in the Ruckus Lennar Support Community.

I would like to know if you require further assistance since our last correspondence. Should you have any questions or if the status of your case has changed, please let me know by responding to this post.

Please feel free to contact if you have any further concerns regarding the same.

Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

pinky_ruckus · ‎04-28-2025

Hello @Kevin4 ,

Greetings!

This is a follow-up in reference to the case you have opened in the Ruckus Lennar Support Community.

I would like to know if you require further assistance since our last correspondence. Should you have any questions or if the status of your case has changed, please let me know by responding to this post.

Please feel free to contact if you have any further concerns regarding the same.

Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

pinky_ruckus · ‎04-30-2025

Hi @Kevin4 ,

Greetings!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

If we do not receive a response from you within 24 hours from the timestamp of this message, your case will proceed to closure.

Thank you.

Best regards,
Pinky Rajendran

RUCKUS Lennar Home Community

How to do Ruckus ICX 7150-C12P Switch health check