Cannot update icx7150

[Rkeiser]

Switch will not update firmware and when in cli it says it is in read only. Also when I try to configure ssl there is no start up config file. tried multiple times and says the same thing. when i show flash it shows "Compressed Pri Code size = 25976488, Version:08.0.80fT211 (SPS08080d.bin)
 Compressed Sec Code size = 25976488, Version:08.0.80fT211 (SPR08080d.bin)
 Compressed Boot-Monitor Image size = 786944, Version:10.1.15T225
" It wont take the actual image 08090f to upgrade to ufi.

[Rkeiser]

I performed software recovery steps per the guide and executed the reload command. The above string is what i got after the reload. Why is it showing next to the versions SPR/SPS 08080d.bin?

[Imran_ruckus]

Hi @Rkeiser 

Greetings!!!

Thank you for the response and the information you shared.

Could you please let me know what is the light status on the Switch panel now? (Please refer to the below screenshot and share a picture of the same)

Also, please enter the below commands once you log in to CLI and share the output.

Note: Hit Enter to accept each command 

enable 

show version

show flash

Please let me know if you have any queries in this regard.

Thank you again for your patience.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Rkeiser]

Below is the information requested.

ICX7150-C12-Switch#show version
Copyright (c) 2017 Ruckus Wireless, Inc. All rights reserved.
UNIT 1: compiled on Apr 6 2020 at 22:29:25 labeled as SPS08080f
(25976488 bytes) from Primary SPS08080d.bin
SW: Version 08.0.80fT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.14T225 (mnz10115)
Compiled on Thu Nov 15 12:59:22 2018

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3816R0BB
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 1 minute(s) 19 second(s)
The system started at 00:09:14 GMT+00 Sat Jan 01 2000

The system : started=cold start

ICX7150-C12-Switch#
ICX7150-C12-Switch#
ICX7150-C12-Switch#TFTP session timed out
show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 25976488, Version:08.0.80fT211 (SPS08080d.bin)
Compressed Sec Code size = 25976488, Version:08.0.80fT211 (SPR08080d.bin)
Compressed Boot-Monitor Image size = 786944, Version:10.1.14T225
Code Flash Free Space = 1204994048

The  version and flash reverted to 0808f after a power outage.

Respectfully,

Rey

[Imran_ruckus]

Hi @Rkeiser 

Greetings,

Thank you for your response and the provided update. 

I have observed that your Switch is currently operating on version 08080d on both the partitions.

We highly recommend upgrading the Switch to the suggested version. 

The proposed upgrade path entails transitioning from 08.0.80d (your current Switch version) to 08.0.80f and finally to 08.0.95g.

For detailed instructions on how to proceed with the upgrade process, kindly refer to the RUCKUS Lennar Knowledge Base self-help article accessible via the following link: 

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-upgrade-RUCKUS-ICX-71...

Should you encounter any challenges or require assistance at any stage of the upgrade, please do not hesitate to reach out. 

Your patience and cooperation throughout this process are greatly appreciated.

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

[Rkeiser]

I was getting UBISF errors and could not load a config file. Should I do a full factory reset and attempt to do the recommended steps as mentioned above?

ICX7150-C12-Switch#UBIFS error (ubi0:0 pid 688): ubifs_check_node: bad node at L EB 10