Cannot update icx7150

[Rkeiser]

Switch will not update firmware and when in cli it says it is in read only. Also when I try to configure ssl there is no start up config file. tried multiple times and says the same thing. when i show flash it shows "Compressed Pri Code size = 25976488, Version:08.0.80fT211 (SPS08080d.bin)
 Compressed Sec Code size = 25976488, Version:08.0.80fT211 (SPR08080d.bin)
 Compressed Boot-Monitor Image size = 786944, Version:10.1.15T225
" It wont take the actual image 08090f to upgrade to ufi.

[Rkeiser]

Which software you recommend I download?

[Rkeiser]

Do I download the software in the link provided or do I download a different one?

[Imran_ruckus]

Hi @Rkeiser 

Thank you for the response.

Please follow the same software and other steps as mentioned in the Software recovery guide.

Please share the screenshots if stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[Rkeiser]

Followed the instructions but still getting read-only system error.

"

Starting kernel ...

Mounting file system...
booting with 4.4 kernel
NAND Type: Micron NAND 2GiB (x 1)
PLATFORM MN
dd cmd: UBI
Config partition mounted
Resource partition is mounted!!
UBIFS error (ubi0:0 pid 566): ubifs_check_node: bad magic 0x6101821, expected 0x6101831
UBIFS error (ubi0:0 pid 566): ubifs_check_node: bad node at LEB 10:476376
Not a node, first 24 bytes:
00000000: 21 18 10 06 8b 85 0f 59 63 54 00 00 00 00 00 02 58 00 00 00 09 00 00 00 !......YcT......X.......
UBIFS error (ubi0:0 pid 566): ubifs_read_node: expected node type 9
UBIFS error (ubi0:0 pid 566): ubifs_iget: failed to read inode 80, error -117
UBIFS error (ubi0:0 pid 566): ubifs_lookup: dead directory entry '.images', error -117
UBIFS error (ubi0:0 pid 688): ubifs_check_node: bad magic 0x6101821, expected 0x6101831
UBIFS error (ubi0:0 pid 688): ubifs_check_node: bad node at LEB 10:476376
Not a node, first 24 bytes:
00000000: 21 18 10 06 8b 85 0f 59 63 54 00 00 00 00 00 02 58 00 00 00 09 00 00 00 !......YcT......X.......
UBIFS error (ubi0:0 pid 688): ubifs_read_node: expected node type 9
UBIFS error (ubi0:0 pid 688): ubifs_iget: failed to read inode 80, error -117
UBIFS error (ubi0:0 pid 688): ubifs_lookup: dead directory entry '.images', error -117
mkdir: can't create directory '/fast_iron/.images': Structure needs cleaning
Please download UFI image to install packages
/etc/process_packages.sh: line 148: can't create /.pkg/error.log: nonexistent directory
Package installation is incomplete, related functionalities may not be available
dhcpd executable file is not present.
Starting up system statistics daemon...
Starting systatsd done
Starting up health monitor daemon...
Log Level 7: Daemonized systatsd
Systatsd Logging Env is not set, initializing loglevel to: 7
Setting connection to systemlogger
Starting hmond done
Hmond Logging Env is not set, initializing loglelvel to: I
Setting connection to systemlogger
Backup is fine
Kernel crashdump is disabled.
/etc/backup_infra.sh: line 633: can't create /fast_iron/.hash_track.md5: Read-only file system
dma_mem_base: 0x96000000, dma_mem_len: 0x8000000, warm_mem_base: 0x9f500000, warm_mem_len: 0xb00000
Creating TUN device
mv: can't rename '/fast_iron/logs/tpm_infra_init.log': Read-only file system
Starting TPM Infra
/etc/tpm-infra.sh: line 100: can't create /fast_iron/logs/tpm_infra_init.log: Read-only file system
Group tss and User tss created
/etc/tpm-infra.sh: line 100: can't create /fast_iron/logs/tpm_infra_init.log: Read-only file system
kernel.hostname = localhost
hostname set to localhost
/etc/tpm-infra.sh: line 100: can't create /fast_iron/logs/tpm_infra_init.log: Read-only file system
Starting TCSD Daemon
/etc/tpm-infra.sh: line 100: can't create /fast_iron/logs/tpm_infra_init.log: Read-only file system
TCSD Up and Running
/etc/tpm-infra.sh: line 100: can't create /fast_iron/logs/tpm_infra_init.log: Read-only file system
Enabling time stamp.
/etc/init.sh: line 1: can't create /fast_iron/logs/bootmsg: Read-only file system

^C
show flash
show version
Starting the FastIron.
USER=root
HOME=/
GCOV_PREFIX=/fast_iron
ethaddr=c0:c5:20:9c:2b:c4?
TERM=vt102
PATH=/sbin:/usr/sbin:/bin:/usr/bin
crashkernel=64M@0x70000000
ip=192.168.0.5:192.168.0.3:192.168.0.4:255.255.255.0:MN:eth0:off
SHELL=/bin/sh
PWD=/
i2c-0 i2c Broadcom iProc I2C adapter I2C adapter 2
i2c-1 i2c Broadcom iProc I2C adapter I2C adapter 2
sil_flash: Unable to open image meta data file, err Read-only file system
sil_flash: Unable to open image meta data file, err Read-only file system
FIPS Disabled:PORT NOT DISABLED
platform type 90
OS>Enabling Console Logging
Applying factory defaults..
INFO: startup config data is not available, try to read from backup
INFO: startup config data in the backup area is not available
Hotplugger Daemon Initialized ..
External USB disk is not mounted or plugged in.
set_board_level: gi_board_type = 116[ 117.846470] linux-kernel-bde: map phys range 0x3200000-0x3240000 to 0xb0e0e000-0xb0e4e000
[ 118.091828] linux-kernel-bde: map phys range 0x88100000-0x90100000 to 0xa8c8f000-0xb0c8f000
DMA pool size: 134217728
PHY Reset De-asserted
sw_pp_sdk_init:136 ToR init
SOC unit 0 attached to PCI device BCM56160_B0
InitializeLicense: VLSaddAndLoadLicenseStorage failed - 166(STORE_ALREADY_EXISTS)
Error: license initialization failed - 1
Firmware version from File: 2.1.1
Pre Parsing Config Data ...
INFO: empty config data in the primary area, try to read from backup
INFO: empty config data in the backup area also

Warning: This operation would close all existing SSH connection.
Parsing Config Data ...
INFO: empty config data in the primary area, try to read from backup
INFO: empty config data in the backup area also

Going to sleep forever...
Warning! Remove stack enable because default stack ports have configuration

Successfully notified stack role 'none' to hmond

System initialization completed...console going online.
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Feb 23 2021 at 00:00:27 labeled as SPS08090k
(29360128 bytes) from Tftp SPS08090k.bin (UFI)
SW: Version 08.0.90kT211
Compressed Secondary Boot Code size = 786944, Version:10.1.15T225 (mnz10115)
Compiled on Thu Jan 31 07:08:55 2019

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3816R0BB
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 7 second(s)
The system started at 05:51:47 GMT+00 Mon Jan 03 2000

The system : started=warm start reloaded=by "reload"

==========================================================================
========== WARNING: Boot-monitor version mismatch!!! ==========
========== Please use "show boot-monitor" command for details ==========
==========================================================================

Press Enter key to login
show flash

User Access Verification

Please Enter Login Name: show version
Please Enter Password:

Press Enter key to login

Creating certificate, please wait...

SSL Client Certificate is successfully created

PS 1, Internal Power supply detected.
PS 1, Internal Power supply is up.
PoE: Stack unit 1 PS 1, Internal Power supply with 124000 mwatts capacity is up
PoE Info: Adding new 54V capacity of 124000 mW, total capacity is 124000, total free capacity is 124000
PoE Info: PoE module 1 of Unit 1 on ports 1/1/1 to 1/1/12 detected. Initializing....
2000 log entries of PoE Event Trace Log Buffer is allocated on unit 1 for unit 1
PoE Event Trace Logging enabled for unit 1
PoE Info: PoE module 1 of Unit 1 initialization is done.
PoE: Power enabled on port 1/1/5.
PoE: Power enabled on port 1/1/6.
TFTP session timed out
TFTP session timed out
TFTP session timed out

User login failure.

Press Enter key to login

User Access Verification

Please Enter Login Name: super
Please Enter Password:
User login successful.

User super login successful with default password. Please change the password.

Enter the new password for user super :TFTP session timed out
TFTP session timed out

Enter the reconfirm password for user super:
Creating certificate, please wait...

SSL Client Certificate is successfully created

New-password and Re-confirm password are not identical

Enter the new password for user super :
Enter the reconfirm password for user super:
Password modified successfully for user super

Authentication is enabled in the device for Console/WEB/SSH.

ICX7150-C12-Switch>TFTP session timed out

ICX7150-C12-Switch>ena
No password has been assigned yet...
ICX7150-C12-Switch#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 29360128, Version:08.0.90kT211 (SPS08080d.bin)
Compressed Sec Code size = 29360128, Version:08.0.90kT211 (SPR08080d.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.14T225 (mnz10114)
Compressed Sec Boot Code size = 786944, Version:10.1.15T225 (mnz10115)
Code Flash Free Space = 1204994048
ICX7150-C12-Switch#show version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Feb 23 2021 at 00:00:27 labeled as SPS08090k
(29360128 bytes) from Tftp SPS08090k.bin (UFI)
SW: Version 08.0.90kT211
Compressed Secondary Boot Code size = 786944, Version:10.1.15T225 (mnz10115)
Compiled on Thu Jan 31 07:08:55 2019"

[Imran_ruckus]

Hi @Rkeiser 

Greetings!!!

Thank you for the response and the update.

Could you please let me know if you performed software recovery steps and executed the command reload at the end?

Please confirm and let me know if you have any queries in this regard.

Thank you again for your patience.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.