RUCKUS Community Forums are now in READ-ONLY mode while we migrate to a new platform.
You will still be able to read posts and knowledge articles, but will be unable to post new content until Go Live on the new platform Monday August 17.
Lennar Smart Home customers: please contact [email protected] for assistance during the week of August 9-17.
04-30-2024 05:52 PM - edited 05-01-2024 07:07 AM
Hi,
I have two switches, ICX7450 and ICX7550. Below is a table with switch models and tested image SW versions. On both switches, I could not get Digital Optical Monitoring to work on Ruckus vendor-provided part numbers: 33211-100 & 33210-100, but can get Digital Optical Monitoring to work on Brocade vendor-provided part numbers: 33211-100 & 33210-100 not matter the image versions .
Global DOM settings
optical-monitor
optical-monitor down-port-enable
optical-monitor non-ruckus-optic-enable
Show Optic
STBD_SAS#sh optic 1/1/4
Port Temperature Voltage Tx Power Rx Power Tx Bias Current
+-----+-------------+-------------+-------------+-------------+---------------+
1/1/4 29.9140 C 3.3328 volts -005.0196 dBm -026.3827 dBm 6.392 mA
Normal Normal Normal Low-Alarm Normal
STBD_SAS#sh optic 1/1/6
1G M-SX on port 1/1/6 is not capable of optical monitoring.
Show Media
Note: 1/1/4 is the Brocade vendor-provided SFP
Note: 1/1/6 is the Ruckus vendor-provided SFP
STBD_SAS#sh media eth 1/1/4
Port 1/1/4: Type : 1GE M-SX(SFP)
Vendor: RUCKUS Version: A
Part# : 33210-100 Serial#: TAF217060000DV4
STBD_SAS#sh media eth 1/1/6
Port 1/1/6: Type : 1GE M-SX(SFP)
Vendor: RUCKUS Version: A
Part# : 33210-100 Serial#: TAU121110000188
Show Media Validation
STBD_SAS>sh media validation
Port Supported Vendor Type
---------------------------------------------------------------------
1/1/4 Yes RUCKUS Type : 1GE M-SX(SFP)
1/1/6 Yes RUCKUS Type : 1GE M-SX(SFP)
Syslog
Log on both switches suggest that the Ruckus-provided SFP is not Brocade qualified
Enabling Port defined Optical Monitoring
en
config t
int ethe 1/1/6
optical-monitor
1G M-SX(SFP) on port 1/1/XX is not capable of optical monitoring
| Model | SW Version | SFP Vendor 1 | SFP Part Number | DOM Supported | DOM Works?
| SFP Vendor 2 | SFP Part Number | DOM Supported | DOM Works?
|
| ICX7450 | 08.0.70d | Ruckus | 33211-100/ 33210-100 | Yes | No | Brocade | 33211-100/ 33210-100 | Yes | No |
| ICX7450 | 08.0.80f | Ruckus | 33211-100/ 33210-100 | Yes | No | Brocade | 33211-100/ 33210-100 | Yes | No |
| ICX7450 | 08.0.95d | Ruckus | 33211-100/ 33210-100 | Yes | No | Brocade | 33211-100/ 33210-100 | Yes | Yes |
| ICX7450 | 08.0.95n | Ruckus | 33211-100/ 33210-100 | Yes | No | Brocade | 33211-100/ 33210-100 | Yes | Yes |
| ICX7550 | 08.0.95f | Ruckus | 33211-100/ 33210-100 | Yes | No | Brocade | 33211-100/ 33210-100 | Yes | Yes |
| ICX7550 | 08.0.95n | Ruckus | 33211-100/ 33210-100 | Yes | No | Brocade | 33211-100/ 33210-100 | Yes | Yes |
Solved! Go to Solution.
05-01-2024 07:32 AM - edited 05-01-2024 07:33 AM
Thank you for the update.
Below is my observation :
We have an issue going on with that part number ( 33210-100), This is the defect number FI-264785 and it should be fixed in 08095j.
However if it still seeing in 8095n I would recommend you to open a case with us so that we can check it internally.
Please log a ticket with the below link so that we will help you further
https://support.ruckuswireless.com/contact-us
I hope this information helps you
Please feel free to leave us a message if any concerns
Note: Please feel free to mark the post as ACCEPTED SOLUTIONS if its addressed your query.
Thanks
05-04-2024 08:08 AM
Hi Donjb207
Ack and Thanks.
