ICX 7150 to Ruckus ZD1200 w/H510 WAP

[p_tech]

hello Newbie question.
I am trying to connect a ZD1200 via an ICX 7150 switch to H510 APs.
 vlan 1 is native /Vlan 20 public ssid /Vlan 30 for members / Vlan 40 for media and Vlan  100 for wired connections.

I have the following config but unable to get the ZD on port 1/1/1 to connect to the APs on ports 1/1/3 - 1/1/12.

The source internet port is 1/2/1

-------------------------------------------------------------------

!
ver 08.0.61aT213
!
stack unit 1
  module 1 icx7150-24p-poe-port-management-module
  module 2 icx7150-2-copper-port-2g-module
  module 3 icx7150-4-sfp-plus-port-40g-module
!
!
!
!
!
vlan 1 name DEFAULT-VLAN by port
!
vlan 10 by port
 tagged ethe 1/1/1 ethe 1/1/11
!
vlan 20 by port
 tagged ethe 1/1/1 ethe 1/1/3
 router-interface ve 20
!
vlan 30 by port
 tagged ethe 1/1/1
 router-interface ve 30
!
vlan 40 by port
 tagged ethe 1/1/1
 router-interface ve 40
!
vlan 100 by port
 tagged ethe 1/1/1 ethe 1/1/7
 untagged ethe 1/1/8 to 1/1/9
 router-interface ve 100
!
!
!
aaa authentication web-server default local
aaa authentication login default local
boot sys fl sec
no ip dhcp-client auto-update enable
ip dhcp-server enable
no ip dhcp-server mgmt
!
ip dhcp-server pool public
 dhcp-default-router 172.16.1.1
 dns-server 8.8.8.8
 excluded-address 172.16.1.1
 lease 0 1 0
 network 172.16.1.0 255.255.255.0
 deploy
!
!
ip dhcp-server pool members
 dhcp-default-router 172.16.2.1
 dns-server  8.8.8.8
 lease 0 12 0
 network 172.16.2.0 255.255.255.0
 deploy
!
!
ip dhcp-server pool media
 dhcp-default-router 172.16.3.1
 dns-server  8.8.8.8
 lease 0 4 0
 network 172.16.3.0 255.255.255.0
 deploy
!
!
ip dhcp-server pool vlan100
 dhcp-default-router 10.10.64.1
 dns-server 10.10.64.1 8.8.8.8
 excluded-address 10.10.64.1 10.10.64.50
 lease 1 0 0
 network 10.10.64.0 255.255.254.0
 deploy
!
ip default-network 10.10.64.0/23
ip dns domain-list CI_LA
ip dns server-address 10.10.64.1 8.8.8.8
ip route 10.10.64.0/23 ethernet 1/2/1
ip route 172.16.1.0/24 ethernet 1/2/1
!
!
!
!
!
!
!
!
!
!
interface ethernet 1/1/1
 dual-mode  10
!
interface ethernet 1/1/3
 inline power
!
interface ethernet 1/1/4
 inline power
!
interface ethernet 1/1/5
 inline power
!
interface ethernet 1/1/6
 inline power
!
interface ethernet 1/1/7
 inline power
!
interface ethernet 1/1/8
 inline power
!
interface ethernet 1/1/9
 inline power
!
interface ethernet 1/1/10
 inline power
!
interface ethernet 1/1/11
 inline power
!
interface ethernet 1/1/12
 inline power
!
interface ethernet 1/3/2
 speed-duplex 1000-full
!
interface ethernet 1/3/4
 speed-duplex 1000-full
!
interface ve 20
 ip address 172.16.1.1 255.255.255.0
!
interface ve 100
 ip address 10.10.64.1 255.255.254.0
!
!
interface ve 30
 ip address 172.16.2.1 255.255.255.0
!
interface ve 40
 ip address 172.16.3.1 255.255.255.0
!
!
!
!
!
!
!
end

 

[p_tech]

PORT-VLAN 10, Name MGMT, Priority level0, Spanning tree Off
 Untagged Ports: (U1/M1)   1
   Tagged Ports: None
   Uplink Ports: None
 DualMode Ports: (U1/M1)   3   4   5   6   7   8   9  10  11  12

[syamantakomer]

Still I do not see interface 1/1/1 in Dual port mode for VLAN 10.

Kindly correct this or plug the ZD on any interface 3-12 for testing and it should get an IP and should be reachable from switch.

You may also factory reset the ZD once to see if it gets an IP then.

[p_tech]

thanks for your assistance so far.

Still no joy.  I didn't factory reset the ZD yet but did get this when I changed the vlan from 10 to 1

[syamantakomer]

Hi P-Tech,

Ruckus ZD and APs works on default VLAN 1 as untagged. If you change the VLAN from 1 to any other VLAN, this will become a tagged VLAN.

I am again giving you the requirements for ZD AP VLAN configuration.

Switch port config for ZD:
Port should be trunk with VLAN 10 in dual mode and rest VLANs as tagged.

Switch port config for ZD:
Port should be trunk with VLAN 10 in dual mode and rest VLANs as tagged.

ZD:
It should be set to DHCP and VLAN set to 1.

If above configurations are correct on switch port/ZD then AP and ZD both will get the IP on VLAN 10 and will auto connect without any further intervention.

I can see that ZD is getting an IP now from DHCP but it is getting a incorrect gateway.

Double check if DHCP configured correctly on switch.

If you still see the issue, I will advise to raise a case with support.

[p_tech]

this the output when I show vlan 10 on the switch

PORT-VLAN 10, Name MGMT, Priority level0, Spanning tree Off
 Untagged Ports: None
   Tagged Ports: None
   Uplink Ports: None
 DualMode Ports: (U1/M1)   1   3   4   5   6   7   8   9  10  11  12
 Mac-Vlan Ports: None
     Monitoring: Disabled