Error at boot relatet dlogger.boot

[pixel24]

Hello everyone,

I’m new here, so first of all, a “hello” to the group. I’ve recently purchased two used ICX 7150-C12P 2X10G switches for my home and have installed them. I’m still a beginner and want to dive deeper into Ruckus products.

The two switches didn’t come with the latest firmware, so I’d like to update them. Current version on delivery:

telnet@sw01#show version
  Copyright (c) 1996-2017 Brocade Communications Systems, Inc. All rights reserved.
    UNIT 1: compiled on Feb 17 2017 at 16:03:13 labeled as SPS08060
      (23946048 bytes) from Primary SPS08060.bin
        SW: Version 08.0.60T211 
      Compressed Boot-Monitor Image size = 786944, Version:10.1.09T225 ()
       Compiled on Sat Feb 18 00:15:43 2017

  HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X10GR POE 12-port Management Module
      Serial  #:FEK3209N02P
      Current License: 2X10GR  
      P-ASIC  0: type B160, rev 11  Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
 1000 MHz ARM processor ARMv7 88 MHz bus
 8192 KB boot flash memory
 2048 MB code flash memory
 1024 MB DRAM
STACKID 1  system uptime is 1 day(s) 15 hour(s) 35 minute(s) 39 second(s) 
The system started at 08:24:55 GMT+00 Sat Jan 01 2000             

The system : started=warm start   reloaded=by "reload"

telnet@sw01#show flash
Stack unit 1:
  Compressed Pri Code size = 23946048, Version:08.0.60T211 (SPS08060.bin)
  Compressed Sec Code size = 23946048, Version:08.0.60T211 (SPS08060.bin)
  Compressed Boot-Monitor Image size = 786944, Version:10.1.09T225
  Code Flash Free Space = 1307099136

I watched several videos from Ruckus and learned that if I want to update from a version equal to or lower than 08.0.70, I need an intermediate update to "08090." Therefore, I proceeded with the installation as follows:

en
copy tftp flash 192.168.83.141 mnz10115.bin bootrom
copy tftp flash 192.168.83.141 SPS08090k.bin primary
copy tftp flash 192.168.83.141 SPS08090k.bin secondary
era startup
boot system flash primary

en
copy tftp flash 192.168.83.141 SPS08090kufi.bin primary
copy tftp flash 192.168.83.141 SPS08090kufi.bin secondary
era startup
boot system flash primary

boot system flash secondary

copy tftp flash 192.168.83.141 SPS09010j_cd5ufi.bin secondary
boot system flash secondary

en
conf t
boot system flash secondary
write memory

Everything worked without any error messages. However, when I follow the boot process via the terminal, I always see the following messages when booting from the secondary image:

cp: can't stat '/.pkg/libpam/etc/*': No such file or directory  
                                                              Starting mgmt monitor scrit
                                                                                         Creating TUN device
...
Creating the first Tap interface
ERROR: Failure in ifconfig br0
ERROR: Failure in gw add
...
Thu Jan  1 00:02:52 UTC 1970:Starting the FastIron.
rm: can't remove 'dlogger.boot': No such file or directory  
                                                          cp: can't stat '/fast_iron/dlogger.boot': No such file or rectory

What did I do wrong or forget to do?

 with best

[Chandini]

Hi Pixel24 

Thank you for reaching us 

I noticed that the version that is running on the switch is 8060. Please follow the below path

• 8060 -> 8080f -> 8090k 

Below are few links for reference:

• https://community.ruckuswireless.com/t5/RUCKUS-Self-Help/How-to-upgrade-from-older-firmware-versions...
• https://community.ruckuswireless.com/t5/ICX-Switches/Upgrade-path-from-older-images-ICX/m-p/63735

Thanks 

[Yarenis]

Hi @pixel24

Since the upgrade path was not followed, the boot image is now corrupted, so let me add the documentation for upgrading the device:

How to upgrade from the current code to the recommended code:

Software Mandatory Upgrade Steps from a Pre-08.0.90 Non-UFI Version to a 08.0.90 UFI Version

Document source:

https://docs.commscope.com/bundle/fastiron-08090-upgradeguide/page/GUID-5DD7EE86-6988-4CA7-81D2-22EA...

 Software Mandatory Upgrade Steps from a Pre-08.0.90 Non-UFI Version to a 08.0.95 UFI Version

https://docs.commscope.com/bundle/fastiron-08095-upgradeguide/page/GUID-5DD7EE86-6988-4CA7-81D2-22EA...