cancel
Showing results for 
Search instead for 
Did you mean: 

3xR700 speedflex MAX 300mbit on GIGALAN

angelo_de_laat
New Contributor
Hi,

I have 3 R700 APS with no ZD.

Have tried several sw releases but currently running 100.1.0.0.432 as this has the highest throughput in WIFI and LAN. 

running IPERF3 while replacing two APS with PCs give me:

Server listening on 5201-----------------------------------------------------------
Accepted connection from 192.168.100.1, port 37418
[  5] local 192.168.100.69 port 5201 connected to 192.168.100.1 port 23843
[ ID] Interval           Transfer     Bandwidth
[  5]   0.00-1.00   sec  92.3 MBytes   774 Mbits/sec
[  5]   1.00-2.00   sec  97.9 MBytes   822 Mbits/sec
[  5]   2.00-3.00   sec   103 MBytes   860 Mbits/sec
[  5]   3.00-4.00   sec  91.5 MBytes   768 Mbits/sec
[  5]   4.00-5.00   sec  94.2 MBytes   790 Mbits/sec
[  5]   5.00-6.00   sec   101 MBytes   851 Mbits/sec
[  5]   6.00-7.00   sec   102 MBytes   859 Mbits/sec
[  5]   7.00-8.00   sec   101 MBytes   851 Mbits/sec
[  5]   8.00-9.00   sec   103 MBytes   862 Mbits/sec
[  5]   9.00-10.00  sec   103 MBytes   861 Mbits/sec
[  5]  10.00-10.12  sec  10.2 MBytes   739 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth
[  5]   0.00-10.12  sec  0.00 Bytes  0.00 bits/sec                  sender
[  5]   0.00-10.12  sec   999 MBytes   829 Mbits/sec                  receivertch and ethernet cables 


So, 829 Mbits/sec is fine and I think we can eliminate switch and/or cable issues.

Ruckus is giving me MAX 300mbps using SpeedFlex test (tried several ways with all 3 APS)

ethernetport is configured as trunkport
bridged to WAN
802.1X disabled
option 82 enabled
fingerprinting enabled
giving me a 1000M full in the status view:

LAN Port StatusRefresh
Port  Interface  802.1X  Logical Link  Physical Link      Label
0 eth0 None Up Up 1000Mbps full 10/100/1000 PoE 
1 eth1 None Down Down 10/100/1000


is there a setting I`m overlooking to enable full speed between APS?




2 REPLIES 2

angelo_de_laat
New Contributor
can somebody please but some questions in reply so I can investigate or tell me what I overlooked..

syamantakomer
Community Admin
Community Admin
Hi Angelo,

R700 is a 3x3x:3 AP, means it will provide highest data rate when a compatible client is connected on 5GHz on 80MHz channel.

Image_ images_messages_5f91c453135b77e247a26f3c_83f6c53e4fdabb3e9dfd4631436d416a_RackMultipart202009161175081fn-070d98dc-a6d5-4f99-9c0d-807570ff902b-2034876613.png1600260778

Data rate also depends upon so many factors like, RF noise/interference, type of material used in physical environment where APs are deployed, multipath, etc.

Start checking with supported data rates on the UE WiFi card specification and how many spacial streams it supports. Then check if AP is configured with 80MHz channelization and client is connecting on 5GHz.

For example, my laptop's wifi card only supports 2x2 antenna chains and it can go upto 867Mbps on 5GHz radio.

If I try to connect my laptop to an AP, which support gigbit speed, still I cannot cross the maximum supported speed by the client device WiFi card.

Image_ images_messages_5f91c453135b77e247a26f3c_e4d946b59d706557f019f00a8a8ab6cb_RackMultipart2020091664533v5xe-b4655fed-e709-4f08-9787-31e22e72a0c3-844506868.png1600261747

Regards,
Syamantak Omer

Syamantak Omer
Sr.Staff TSE | CWNA | CCNA | RCWA | RASZA | RICXI
RUCKUS Networks, CommScope!
Follow me on LinkedIn