cancel
Showing results for 
Search instead for 
Did you mean: 

Ruckus R310 unleashed second AP not working

chip_boy
New Contributor II

Hello, I have a small single point R310 network. I need to add one additional AP.
They connected through the single switch, ping works.

But second AP currently stuck in "Building the Unleashed Network. It may take a few minutes."

Here's what I tried:
1) Factory reset multiple times
2) set director <Master IP>
3) upgrade fw to latest on both units

In upgrade section I can see this new AP and it's status - member.
Executing on this AP

 

get election

 

I get the following:

 

mac_address ipaddress role configID station_rate free_memory mesh_enabled mesh_node mesh_node_type model version bak_version systime board_type uptime last_seen
------------------------------------------------------------------------------------------------------------------------------------------------
0c:f4:d5:02:81:30 192.168.10.25 master 1053 35 140136 0 0 0 R310 200.7.10.202.141 200.7.10.202.121 190902 zf7752-3-29-4bss 2 days 5 hrs 3 mins  Sun Apr  2 21:38:22 2023
b4:79:c8:15:43:b0 192.168.10.250 member 1 44 180088 0 0 0 R310 200.7.10.202.141 200.7.10.2.339 0 zf7752-3-29-4bss 2 days 5 hrs 13 mins  Sun Apr  2 21:38:20 2023

 

Need advice on what else I can check.
Thanks.

1 ACCEPTED SOLUTION

chip_boy
New Contributor II
Apr  3 15:07:45 Qlran stamgr: stamgr_is_supported_ap_model():The AP r310 is supported 
Apr  3 15:07:45 Qlran stamgr: stamgr_handle_get_ap_sta():in_req->env=60, contrycode=US  
Apr  3 15:07:45 Qlran stamgr: stamgr_match_countrycode():AP country code US, ZD country code GB  
Apr  3 15:07:45 Qlran stamgr: stamgr_handle_get_ap_sta():ERROR: no cfg AP  

changed country code to US, it worked

View solution in original post

8 REPLIES 8

sanjay_kumar
RUCKUS Team Member

Hi @chip_boy 

Can you try executing the below command and see if it works? This will force the AP to contact the R310 and join it.

set director ip x.x.x.x

x.x.x.x is the Master's IP address (existing R310 AP)

If the above set did not work, then try the below step on Master:
1. Go to Admin/Services | System | IP settings
2. Change the IP from DHCP to Manual (same IP).
3. Reboot the AP and check.

Note : Make sure to take the backup first.

Hello, @sanjay_kumar 

1) Done, but no changes

rkscli: get director
------ Unleashed Info ------
Device role          : ap
Primary Controller   : 192.168.10.25
Secondary Controller : n/a
DHCP Opt43 Code      : 3
  AP is in Stand-alone mode.
OK

2) Done but no changes

ruckus# show config
Protocol Mode= IPv4-Only
Device IP Address:
  Mode= Manual
  IP Address= 192.168.10.25
  Netmask= 255.255.255.0
  Gateway Address= 192.168.10.1
  Primary DNS= 192.168.10.1
  Secondary DNS= 

 

Hi @chip_boy 
Based on the first logs which you have provided, seems like the Member AP is connecting to the Master but is stuck in joining process.
Since the Master AP's IP is set to Manual now, can you try doing a reboot or FD on the Member AP and check.

I believe the 

@sanjay_kumar

Copyright(C) 2016 Ruckus Wireless, Inc. All Rights Reserved.

** Ruckus R310 Unleashed AP: 381809011246

rkscli: reboot
OK
rkscli: Connection to 192.168.10.250 closed by remote host.

and still

rkscli: get director
------ Unleashed Info ------
Device role          : ap
Primary Controller   : 192.168.10.25
Secondary Controller : n/a
DHCP Opt43 Code      : 3
  AP is in Stand-alone mode.
OK