cancel
Showing results for 
Search instead for 
Did you mean: 

Switch icx 7150-c12p is not powering POE, running slow, have to constantly restart.

ramirezcrisaf
New Contributor III

Switch is an icx 7150-c12p.  at the moment no port is providing POE.  I have to use an injector to have the Ruckus AP working.  I have to restart the switch a lot for maybe a port or 2 to work.  Things are working slow as well.  

I have things connected to 9 of the ports and only 4 are showing up.  Switch says POE is ok but it is not. Temperature is ok.   Please see output from switch below.   Please let me know what we can do to replace.  This switch is broken.

telnet@ICX7150-C12 Switch# show chassis
The stack unit 1 chassis info:

Power supply 1 (AC - PoE) present, status ok

Fanless model

Slot 1 Current Temperature: 70.5 deg-C (Sensor 1), 10.0 deg-C (Sensor 2), 57.2 deg-C (Sensor 3), 52.8 deg-C (Sensor 4)
Slot 2 Current Temperature: NA
Slot 3 Current Temperature: NA
Warning level.......: 100.0 deg-C
Shutdown level......: 109.0 deg-C
Boot Prom MAC : d4c1.9e1e.783b
Management MAC: d4c1.9e1e.783b

Port Link State Dupl Speed Trunk Tag Pvid Pri MAC Name
1/1/1 Down None None None None No 1 0 d4c1.9e1e.783b
1/1/2 Down None None None None No 1 0 d4c1.9e1e.783c
1/1/3 Down None None None None No 1 0 d4c1.9e1e.783d
1/1/4 Down None None None None No 1 0 d4c1.9e1e.783e
1/1/5 Down None None None None No 1 0 d4c1.9e1e.783f
1/1/6 Down None None None None No 1 0 d4c1.9e1e.7840
1/1/7 Down None None None None No 1 0 d4c1.9e1e.7841
1/1/8 Up Forward Full 1G None No 1 0 d4c1.9e1e.7842
1/1/9 Up Forward Full 1G None No 1 0 d4c1.9e1e.7843
1/1/10 Down None None None None No 1 0 d4c1.9e1e.7844
1/1/11 Up Forward Full 1G None No 1 0 d4c1.9e1e.7845
1/1/12 Up Forward Full 100M None No 1 0 d4c1.9e1e.7846
1/2/1 Down None None None None No 1 0 d4c1.9e1e.7848
1/2/2 Down None None None None No 1 0 d4c1.9e1e.7849
1/3/1 Down None None None None No 1 0 d4c1.9e1e.784a
1/3/2 Down None None None None No 1 0 d4c1.9e1e.784b
mgmt1 Down None None None None No None 0 d4c1.9e1e.783b

1 ACCEPTED SOLUTION

I am not able to replicate the issue to provide a screen shot.  When trying to do copy tftp flash 192.168.1.166 SPS08095gufi.bin primary, I kept getting errors.  It will start but say that the firmware was not compatible for this hardware or something along those lines.   Using the SPS08090kufi.bin seem to work on CLI but I kept following the web GUI steps.   Now I have SPS08090kufi.bin, see below.  Now that I have the update it seems to want to take the other older firmware upgrades.  

I was able to install 08080f but when warm restarted switch was dead.  I waited a while but had to do a hard power reset.  So, to me the better version is 08090k so far.  We will see how this works.  So far so good.  Thank you for your assistance.  

telnet@ICX7150-C12 Switch# sh flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 29360128, Version:08.0.90kT211 (SPS08090k.bin)
Compressed Sec Code size = 28314668, Version:08.0.61aT213 (SPR08061a.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.18T225 (mnz10118)
Compressed Sec Boot Code size = 786944, Version:10.1.10T225 (mnz10110)
Code Flash Free Space = 1224908800

 

Port Link State Dupl Speed Trunk Tag Pvid Pri MAC Name
1/1/1 Down None None None None No 1 0 d4c1.9e1e.783b
1/1/2 Up Forward Full 100M None No 1 0 d4c1.9e1e.783c
1/1/3 Up Forward Full 1G None No 1 0 d4c1.9e1e.783d
1/1/4 Down None None None None No 1 0 d4c1.9e1e.783e
1/1/5 Up Forward Full 100M None No 1 0 d4c1.9e1e.783f
1/1/6 Down None None None None No 1 0 d4c1.9e1e.7840
1/1/7 Up Forward Full 1G None No 1 0 d4c1.9e1e.7841
1/1/8 Up Forward Full 100M None No 1 0 d4c1.9e1e.7842
1/1/9 Down None None None None No 1 0 d4c1.9e1e.7843
1/1/10 Up Forward Full 1G None No 1 0 d4c1.9e1e.7844
1/1/11 Down None None None None No 1 0 d4c1.9e1e.7845
1/1/12 Up Forward Full 1G None No 1 0 d4c1.9e1e.7846
1/2/1 Up Forward Full 1G None No 1 0 d4c1.9e1e.7848
1/2/2 Down None None None None No 1 0 d4c1.9e1e.7849
1/3/1 Down None None None None No 1 0 d4c1.9e1e.784a
1/3/2 Down None None None None No 1 0 d4c1.9e1e.784b
mgmt1 Down None None None None No None 0 d4c1.9e1e.783b

View solution in original post

25 REPLIES 25

I am not able to replicate the issue to provide a screen shot.  When trying to do copy tftp flash 192.168.1.166 SPS08095gufi.bin primary, I kept getting errors.  It will start but say that the firmware was not compatible for this hardware or something along those lines.   Using the SPS08090kufi.bin seem to work on CLI but I kept following the web GUI steps.   Now I have SPS08090kufi.bin, see below.  Now that I have the update it seems to want to take the other older firmware upgrades.  

I was able to install 08080f but when warm restarted switch was dead.  I waited a while but had to do a hard power reset.  So, to me the better version is 08090k so far.  We will see how this works.  So far so good.  Thank you for your assistance.  

telnet@ICX7150-C12 Switch# sh flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 29360128, Version:08.0.90kT211 (SPS08090k.bin)
Compressed Sec Code size = 28314668, Version:08.0.61aT213 (SPR08061a.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.18T225 (mnz10118)
Compressed Sec Boot Code size = 786944, Version:10.1.10T225 (mnz10110)
Code Flash Free Space = 1224908800

 

Port Link State Dupl Speed Trunk Tag Pvid Pri MAC Name
1/1/1 Down None None None None No 1 0 d4c1.9e1e.783b
1/1/2 Up Forward Full 100M None No 1 0 d4c1.9e1e.783c
1/1/3 Up Forward Full 1G None No 1 0 d4c1.9e1e.783d
1/1/4 Down None None None None No 1 0 d4c1.9e1e.783e
1/1/5 Up Forward Full 100M None No 1 0 d4c1.9e1e.783f
1/1/6 Down None None None None No 1 0 d4c1.9e1e.7840
1/1/7 Up Forward Full 1G None No 1 0 d4c1.9e1e.7841
1/1/8 Up Forward Full 100M None No 1 0 d4c1.9e1e.7842
1/1/9 Down None None None None No 1 0 d4c1.9e1e.7843
1/1/10 Up Forward Full 1G None No 1 0 d4c1.9e1e.7844
1/1/11 Down None None None None No 1 0 d4c1.9e1e.7845
1/1/12 Up Forward Full 1G None No 1 0 d4c1.9e1e.7846
1/2/1 Up Forward Full 1G None No 1 0 d4c1.9e1e.7848
1/2/2 Down None None None None No 1 0 d4c1.9e1e.7849
1/3/1 Down None None None None No 1 0 d4c1.9e1e.784a
1/3/2 Down None None None None No 1 0 d4c1.9e1e.784b
mgmt1 Down None None None None No None 0 d4c1.9e1e.783b

By the way another issue I found was that the switch had the time and date all screwed up.   was on a bad time and on January 1st 2000.  not sure if this will cause any issues, I think it might.  I changed the time and date.  

Hi @ramirezcrisaf 

Thank you for the response and the update.

Time and date will not cause any issues.

As you are now on 08090k version we can use the upgrade tool we recently introduced for that works for Switch version 08080f and above.

Regarding the Switch upgrade process, we recommend transitioning to version 08.0.95g, identified as the stable version for Lennar Home users.

To facilitate this transition, we have recently introduced an upgrade tool tailored to ensure a seamless process. Utilizing this tool is straightforward: users simply need to input the IP Address, Username, and password associated with the Switch into the software interface.

For your convenience, please find the necessary resources below:

1. Download the Upgrade software for Windows: Link: Upgrade Software for Windows

2. Access the Upgrade Software User Manual: Link: Upgrade Tool User Guide for Lennar SmartHome users

We highly value your input and would greatly appreciate your feedback on our upgrade tool. Your insights are instrumental in our ongoing efforts to enhance user experience and ensure the tool meets your needs effectively. Please take a moment to share your thoughts, suggestions, or any issues you encountered while using the tool. Your feedback is invaluable to us and will guide us in further improving the tool for all our users. Thank you for your time and contribution.

Should you require any assistance throughout the process, please do not hesitate to reach out. Your satisfaction is our priority, and we are here to support you every step of the way.

Thank you once again for your patience and cooperation.

 

Best regards,

Imran Sanadi
RUCKUS Lennar Home Community

Hi @ramirezcrisaf 

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

Thank you.

 

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community

Hi @ramirezcrisaf 

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

Thank you.

 

Best regards,
Imran Sanadi
RUCKUS Lennar Home Community