09-03-2024 08:50 AM
Switch is an icx 7150-c12p. at the moment no port is providing POE. I have to use an injector to have the Ruckus AP working. I have to restart the switch a lot for maybe a port or 2 to work. Things are working slow as well.
I have things connected to 9 of the ports and only 4 are showing up. Switch says POE is ok but it is not. Temperature is ok. Please see output from switch below. Please let me know what we can do to replace. This switch is broken.
telnet@ICX7150-C12 Switch# show chassis
The stack unit 1 chassis info:
Power supply 1 (AC - PoE) present, status ok
Fanless model
Slot 1 Current Temperature: 70.5 deg-C (Sensor 1), 10.0 deg-C (Sensor 2), 57.2 deg-C (Sensor 3), 52.8 deg-C (Sensor 4)
Slot 2 Current Temperature: NA
Slot 3 Current Temperature: NA
Warning level.......: 100.0 deg-C
Shutdown level......: 109.0 deg-C
Boot Prom MAC : d4c1.9e1e.783b
Management MAC: d4c1.9e1e.783b
Port Link State Dupl Speed Trunk Tag Pvid Pri MAC Name
1/1/1 Down None None None None No 1 0 d4c1.9e1e.783b
1/1/2 Down None None None None No 1 0 d4c1.9e1e.783c
1/1/3 Down None None None None No 1 0 d4c1.9e1e.783d
1/1/4 Down None None None None No 1 0 d4c1.9e1e.783e
1/1/5 Down None None None None No 1 0 d4c1.9e1e.783f
1/1/6 Down None None None None No 1 0 d4c1.9e1e.7840
1/1/7 Down None None None None No 1 0 d4c1.9e1e.7841
1/1/8 Up Forward Full 1G None No 1 0 d4c1.9e1e.7842
1/1/9 Up Forward Full 1G None No 1 0 d4c1.9e1e.7843
1/1/10 Down None None None None No 1 0 d4c1.9e1e.7844
1/1/11 Up Forward Full 1G None No 1 0 d4c1.9e1e.7845
1/1/12 Up Forward Full 100M None No 1 0 d4c1.9e1e.7846
1/2/1 Down None None None None No 1 0 d4c1.9e1e.7848
1/2/2 Down None None None None No 1 0 d4c1.9e1e.7849
1/3/1 Down None None None None No 1 0 d4c1.9e1e.784a
1/3/2 Down None None None None No 1 0 d4c1.9e1e.784b
mgmt1 Down None None None None No None 0 d4c1.9e1e.783b
Solved! Go to Solution.
09-04-2024 08:35 AM
I am not able to replicate the issue to provide a screen shot. When trying to do copy tftp flash 192.168.1.166 SPS08095gufi.bin primary, I kept getting errors. It will start but say that the firmware was not compatible for this hardware or something along those lines. Using the SPS08090kufi.bin seem to work on CLI but I kept following the web GUI steps. Now I have SPS08090kufi.bin, see below. Now that I have the update it seems to want to take the other older firmware upgrades.
I was able to install 08080f but when warm restarted switch was dead. I waited a while but had to do a hard power reset. So, to me the better version is 08090k so far. We will see how this works. So far so good. Thank you for your assistance.
telnet@ICX7150-C12 Switch# sh flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 29360128, Version:08.0.90kT211 (SPS08090k.bin)
Compressed Sec Code size = 28314668, Version:08.0.61aT213 (SPR08061a.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.18T225 (mnz10118)
Compressed Sec Boot Code size = 786944, Version:10.1.10T225 (mnz10110)
Code Flash Free Space = 1224908800
Port Link State Dupl Speed Trunk Tag Pvid Pri MAC Name
1/1/1 Down None None None None No 1 0 d4c1.9e1e.783b
1/1/2 Up Forward Full 100M None No 1 0 d4c1.9e1e.783c
1/1/3 Up Forward Full 1G None No 1 0 d4c1.9e1e.783d
1/1/4 Down None None None None No 1 0 d4c1.9e1e.783e
1/1/5 Up Forward Full 100M None No 1 0 d4c1.9e1e.783f
1/1/6 Down None None None None No 1 0 d4c1.9e1e.7840
1/1/7 Up Forward Full 1G None No 1 0 d4c1.9e1e.7841
1/1/8 Up Forward Full 100M None No 1 0 d4c1.9e1e.7842
1/1/9 Down None None None None No 1 0 d4c1.9e1e.7843
1/1/10 Up Forward Full 1G None No 1 0 d4c1.9e1e.7844
1/1/11 Down None None None None No 1 0 d4c1.9e1e.7845
1/1/12 Up Forward Full 1G None No 1 0 d4c1.9e1e.7846
1/2/1 Up Forward Full 1G None No 1 0 d4c1.9e1e.7848
1/2/2 Down None None None None No 1 0 d4c1.9e1e.7849
1/3/1 Down None None None None No 1 0 d4c1.9e1e.784a
1/3/2 Down None None None None No 1 0 d4c1.9e1e.784b
mgmt1 Down None None None None No None 0 d4c1.9e1e.783b
09-03-2024 10:49 AM
Hi @ramirezcrisaf
Thank you for your response.
As a note I have updated the article to reflect this change as. Please use 08095g instead of 08095h.
If you have any questions or need further clarification, please do not hesitate to reach out.
Thank you once again for your patience.
Best regards,
Imran Sanadi
RUCKUS Lennar Home Community
09-03-2024 04:06 PM
switch is completely dead now, after updating.
09-03-2024 04:22 PM
Is back on after hard reset but is not taking in new firmware. I would like to try using GUI but I am not able to login
09-03-2024 04:49 PM
I was able to create a new user and configure switch to allow web access. Will try to update on GUI.
09-04-2024 05:32 AM
Hi @ramirezcrisaf
I hope this message finds you well.
Thank you for your response and the update.
Could you please provide the current status of the RUCKUS ICX-7150-C12P switch upgrade? Additionally, if you encountered any errors during the upgrade process using the CLI (Option 2 as outlined in the article), could you kindly share a screenshot of the error?
I appreciate your assistance with these queries. Please let me know if you need any further information.
Thank you once again for your patience and understanding.
Best regards,
Imran Sanadi
RUCKUS Lennar Home Community