Stuck on ICX switch is connecting, no wifi

[jsun]

Stuck on ICX switch is connecting

also receiving this error: Unleashed system only supports ICX firmware version 08.0.90 or later.

I can’t connect to the access point on my Mac terminal it’s telling me that the flash command is not right. Also I can’t install on my work computer to connect through wire

[jsun]

Requested Photos 

Added requested photos, wasn't able to connect through terminal unfortunately

[Imran_ruckus]

Hi @jsun 

Greetings!!!

Thank you for the response and the update.

Please follow the below screenshot and enable Telnet if it is in a disabled state. We will try again to log in via Telnet on CLI.

Once you enable Telnet try to access CLI from the MAC terminal as described below. And share the output of the commands mentioned below in this post.

If you have a MAC device, please try the below process. 

Example "open terminal":

Telnet: Example

nc 10.0.0.132 23 (Format is : nc <ip address of the switch> 23)

If you can log in via Telnet by following the above steps, please share output of the commands mentioned previously.

Please share the output of the above commands or share the screenshots if you are stuck at any step or error (if any) and let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[jsun]

Got it, I had to restart the switch because i couldn't log in. See output below:

show version

  Copyright (c) Ruckus Networks, Inc. All rights reserved.

    UNIT 1: compiled on Sep 22 2019 at 23:54:26 labeled as SPS08090d

      (28660224 bytes) from Primary SPS08090d.bin (UFI)

        SW: Version 08.0.90dT211

      Compressed Primary Boot Code size = 786944, Version:10.1.15T225 (mnz10115)

       Compiled on Thu Jan 31 07:08:55 2019

  HW: Stackable ICX7150-C12-POE

==========================================================================

UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module

      Serial  #:FEK3806S0HS

      Software Package: BASE_SOFT_PACKAGE   

      Current License: 2X1G 

      P-ASIC  0: type B160, rev 11  Chip BCM56160_B0

==========================================================================

UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module

==========================================================================

UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module

==========================================================================

1000 MHz ARM processor ARMv7 88 MHz bus

8192 KB boot flash memory

2048 MB code flash memory

1024 MB DRAM

--More--, next page: Space, next line: Return key, quit: Control-c

STACKID 1  system uptime is 6 minute(s) 24 second(s)

The system started at 00:01:42 GMT+00 Sat Jan 01 2000

The system : started=cold start   

telnet@ICX7150-C12 Switch#

telnet@ICX7150-C12 Switch#show flash

show flash

Stack unit 1:

  NAND Type: Micron NAND 2GiB (x 1)

  Compressed Pri Code size = 28660224, Version:08.0.90dT211 (SPS08090d.bin)

  Compressed Sec Code size = 32539748, Version:08.0.90dT213 (SPR08090d.bin)

  Compressed Pri Boot Code size = 786944, Version:10.1.15T225 (mnz10115)

  Compressed Sec Boot Code size = 786944, Version:10.1.15T225 (mnz10115)

  Code Flash Free Space = 1131073536

[Imran_ruckus]

Hi @jsun 

Thank you for the response and the information you shared.

Could you please share the output of the below commands as well?

enable 

show inline power 
show interface brief

Please let me know if you have any queries in this regard.

Thank you again for your patience.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

[jsun]

Hm, I'm not able to find the switch anymore in my Lanscan or find the IP address. It says "missing hostname and port" when I try to nc in. I tried resetting it as well