12-17-2023 09:59 PM
Ruckus APs are connected, but no internet. ISP wireless have been tested and is working fine. ICX Switch i sin Disconnected status, with status 'ICX Switch is Pending to join' with no IP.
Solved! Go to Solution.
12-18-2023 01:22 PM
Hi @jags
Thank you for the response and the information you shared.
This issue is because your switch is running on the Routing code (SPR). The Switch should run on the Switching code (SPS) to avoid these issues for Lennar home users. Due to a power outage/power spike, the Switch boots up on the other partition which may be running on a ‘Routing Code’ results in causing this issue.
As I can see from the output you shared, your Switch is booted up on the secondary partition which is running on Routing code (SPR) as highlighted in the below screenshot.
Please Enter the below commands in CLI to fix this issue:
Note: Hit Enter to accept each command
enable
copy flash flash secondary
boot system flash secondary yes
Example:
VIDEO LINK AS REFERENCE: https://www.youtube.com/watch?v=Eem1IBgYaWc
ICX7150-24P Router>enable (hit enter to accept the command)
ICX7150-24P Router#copy flash flash secondary (hit enter to accept the command and wait: until the flash finished)
ICX7150-24P Router#boot system flash secondary yes (hit enter to accept the command: the switch will reboot)
Please let me know if you have any queries in this regard.
NOTE: Please feel free to mark the post as ACCEPTED SOLUTIONS.
Thank you again for your patience and understanding.
Best regards,
Imran Sanadi
RUCKUS Lennar Home Community.
12-18-2023 02:13 PM
Thanks Imran. That resolve internet issue.
However, still switch shows disconnected in unleashed dashboard? What I need to do to get that work?
12-18-2023 02:15 PM
After refresh it's fine now, I see switch connected in unleashed dashboard. Thanks for your help.
12-19-2023 05:30 AM
Hi @jags
Thank you for the response and the update.
Great!!! Good to know that the issue is now resolved.
We appreciate your time and patience on this case.
Thank you again for contacting RUCKUS Lennar Home Community and feel free to contact us for future queries.
Have a great day ahead!!!
Best regards,
Imran Sanadi
RUCKUS Lennar Home Community.
12-18-2023 01:10 PM
Here are the requested output.
ICX7150-C12 Router#enable
Incomplete command.
ICX7150-C12 Router#show version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Sep 23 2019 at 00:00:25 labeled as SPR08090d
(32539748 bytes) from Secondary SPR08090d.bin (UFI)
SW: Version 08.0.90dT213
Compressed Secondary Boot Code size = 786944, Version:10.1.15T225 (mnz10115)
Compiled on Thu Jan 31 07:08:55 2019
HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3829R2N2
Software Package: ICX7150_BASE_L3_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
1024 MB DRAM
STACKID 1 system uptime is 4 minute(s) 10 second(s)
The system started at 00:10:01 GMT+00 Sat Jan 01 2000
The system : started=cold start
ICX7150-C12 Router#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 28660224, Version:08.0.90dT211 (SPS08090d.bin)
Compressed Sec Code size = 32539748, Version:08.0.90dT213 (SPR08090d.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.15T225 (mnz10115)
Compressed Sec Boot Code size = 786944, Version:10.1.15T225 (mnz10115)
Code Flash Free Space = 1131053056