09-03-2024 03:34 PM
Hi,
I am having this same problem ("PoE Fatal: Vmain (48V) fault has forced all ports on slot 0 to lose power."). The APs started to sporadically lose POE after a power outage.
I started down this path:How to Upgrade a Switch ICX-7150-C12P using a USB flash drive
However, after the first reboot I have lost access to the console due to constant POE error messages.
I have tried both methods referenced above to "To disable the logs for the PoE error, run the next commands."
Neither worked.
I made to this step (20- Once the switch is running 8080f version, we can proceed to install the 8095hufi, in this version as I mentioned previously, the boot code is not needed to be install separately since it is included in the same file.) but can't really verify versions etc. since my console filled with errors.
What should I try next?
09-12-2024 01:17 PM
Hi @lenar_ruck_user
Greetings!!!
Thank you for the response and the update.
Could you please let me know if you are able to access the CLI using Telnet option?
Please confirm.
Thank you again.
Best regards,
Imran Sanadi
RUCKUS Lennar Home Community.
09-16-2024 07:22 PM
Pinky & Imran,
Thanks for the support! I just double checked and do not have access to Telnet - that service is not listening. I have access to the web interface and ssh but I do not have valid credentials so I cannot log in.
What options do I have at this point? Is there a serial or management interface if I connect directly to the AP? Or, at this point is my only path forward to update the device to do a factory reset. If factory reset is the only option do you have guidance?
Thanks!
09-19-2024 06:43 AM
Hello @lenar_ruck_user ,
Greetings!
This is a follow-up in reference to the case you have opened in the Ruckus Lennar Support Community.
I would like to know if you require further assistance since our last correspondence. Should you have any questions or if the status of your case has changed, please let me know by responding to this post.
Please feel free to contact if you have any further concerns regarding the same.
Best regards,
Pinky Rajendran
RUCKUS Lennar Home Community.
09-21-2024 09:01 AM
Yes, I need support. How do I update the APs without credentials? See my last response:
I do not have access to Telnet - that service is not listening. I have access to the web interface and ssh but I do not have valid credentials so I cannot log in.
What options do I have at this point? Is there a serial or management interface if I connect directly to the AP? Or, at this point is my only path forward to update the device to do a factory reset. If factory reset is the only option do you have guidance?
Thanks
09-23-2024 06:45 AM
Hi @lenar_ruck_user
Greetings!!!
Thank you for the response and the update.
Apologies for the inconvenience.
Please try to connect the RUCKUS ICX-7150-C12P Switch to access the Console CLI access.
To gain console access, please follow the instructions provided in the article linked below: How to Console into the ICX-7150-C12P
While you have the laptop connected to the Switch with a console USB cable and the CLI screen up it asking a username/password, reboot (unplug and plug from the power outlet), and follow the video below.
https://www.youtube.com/watch?v=0ynKwSTpd_A
Once you have successfully recovered the switch password, use the following commands to either modify the existing password or create a new username and password:
enable
configure terminal
device(config)#username super password pass
In this example, the username is ‘super’ and the password is ‘pass’.
To ensure proper authentication, execute the following commands:
device(config)#crypto key generate rsa
device(config)#aaa authentication login default local
device(config)#aaa authentication web-server default local
Please let me know if you have any queries in this regard.
Thank you again for your patience.
Best regards,
Imran Sanadi
RUCKUS Lennar Home Community.