Lennar provided Ruckus ICX 12 port switch is causing disruptions in network

[Itiskashi]

The Lennar provided ruckus system is causing constant disruptions in my home network. When I connect to my devices to the ISP router (wired/wireless), the network is seamless. When I use Ruckus APs the network works fine when rebooted but after a few hours it is disrupted again.

can you assist?

[Itiskashi]

I just rebooted. It is stable for now. I also performed an IP passthrough of the ISP router. The ISP router will not only serve as the model while the Ruckus switch will be my main router. 

[Imran_ruckus]

Hi @Itiskashi

Thank you for the response and the update.

Please monitor the Internet stability and let us know if there are any issues.

Thank you again for your patience.

Best regards,

Imran Sanadi

Lennar Home Community.

[Itiskashi]

Hi Imran,

Still having drop outs. its very random. please help. See below

telnet@ICX7150-C12 Switch>enable
No password has been assigned yet...
telnet@ICX7150-C12 Switch#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 31457280, Version:08.0.95gT211 (SPS08095g.bin)
Compressed Sec Code size = 31457280, Version:08.0.95gT211 (SPS08095g.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.14T225 (mnz10114)
Compressed Sec Boot Code size = 786944, Version:10.1.24T225 (mnz10124)
Code Flash Free Space = 1111916544
telnet@ICX7150-C12 Switch#show version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on May 6 2022 at 23:24:50 labeled as SPS08095g
(31457280 bytes) from Primary SPS08095g.bin (UFI)
SW: Version 08.0.95gT211
Compressed Secondary Boot Code size = 786944, Version:10.1.24T225 (mnz10124)
Compiled on Thu Apr 21 06:08:52 2022

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module

Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8 MB boot flash memory
2 GB code flash memory
1 GB DRAM

[Imran_ruckus]

Hi @Itiskashi

Greetings!!!

Thank you for the update and the information you shared.

As you have 3 access points connected to your ICX-7150-C12P Switch, could you please let me know from how many access points the connection is dropping out? Or does it dropouts on all the Access Points?

Also, please perform and share the output of the below command-

enable 

show lldp neighbors detail

Please let me know if you have any queries in this regard.

Thank you again for your patience.

Best regards,

Imran Sanadi

Lennar Home Community.

[Itiskashi]

How to know which access points are dropping out? I am guess all of them. 

telnet@ICX7150-C12 Switch>enable
No password has been assigned yet...
telnet@ICX7150-C12 Switch#show lldp neighbors detail
LLDP is not running