ICX7150-C12P after power outage

[pptp]

Hello,

After a power outage of several days, it appears the switch is running SPR but it looks like both my primary and secondary code both say SPS so I am unsure how to fix this:

SSH@ICX7150-C12 Router>enable
No password has been assigned yet...
SSH@ICX7150-C12 Router#show version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Jun 6 2024 at 08:46:54 labeled as SPR08095p
(33554432 bytes) from Primary SPS08080d.bin (UFI)
SW: Version 08.0.95pT213
Compressed Primary Boot Code size = 786944, Version:10.1.26T225 (mnz10126)
Compiled on Tue Nov 29 12:43:26 2022

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3817Q8F6
Software Package: ICX7150_BASE_L3_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8 MB boot flash memory
2 GB code flash memory
1 GB DRAM
STACKID 1 system uptime is 2 minute(s) 23 second(s)
The system started at 13:05:59 GMT+00 Thu Jun 06 2024

The system : started=warm start reloaded=by "reload"

SSH@ICX7150-C12 Router#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 33554432, Version:08.0.95pT213 (SPS08080d.bin)
Compressed Sec Code size = 33554432, Version:08.0.95pT213 (SPS08080d.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.26T225 (mnz10126)
Compressed Sec Boot Code size = 786944, Version:10.1.14T225 (mnz10114)
Code Flash Free Space = 1256574976
SSH@ICX7150-C12 Router#

[pinky_ruckus]

Hello @pptp ,

Greetings!

Thank you for contacting RUCKUS Lennar Home Community.

I hope you are doing well!!!

Thank you for the information you shared.

As per the case description, I understand that your RUCKUS setup is not working after the power outage.

I would request you to please run the following command which will help you to fix the issue.

Please enter the below commands once you log in to CLI of the Switch

ICX7150-24P Router>enable (hit enter to accept the command) 
ICX7150-24P Router#copy flash flash secondary (hit enter to accept the command and wait: until the flash finished) 

ICX7150-24P Router#write memory
ICX7150-24P Router#boot system flash secondary yes (hit enter to accept the command: the switch will reboot)

Please follow the above steps and let us know if you have any queries in this regard.

Thank you for your patience and understanding.

Regards,

Pinky Rajendran

RUCKUS Lennar Home Community

[pptp]

Hello,

This is what happens with those prompts:

SSH@ICX7150-C12 Router>enable
No password has been assigned yet...
SSH@ICX7150-C12 Router#copy flash flash secondary

Unable to find a UFI image copy from. Please reload master with appropriate UFI image to proceed with flash-flash copy
SSH@ICX7150-C12 Router#

[pinky_ruckus]

Hello @pptp ,

Thank you for the response.

Could you please try to upgrade the Switch version as the Switch is running on an older non UFI version?

Please follow the below RUCKUS Lennar Knowledge base self-help article which will help you to upgrade the switch to the recommended version

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-upgrade-RUCKUS-ICX-71...

Please follow the process explained in the article and let me know if you have any queries in this regard.

Thank you again. We appreciate your patience and understanding.

Best regards,

Pinky Rajendran

RUCKUS Lennar Home Community.

[pptp]

Hello,

I followed those instructions and I believe it is now running SPS?

SSH@ICX7150-C12 Switch#show version
Copyright (c) Ruckus Networks, Inc. All rights reserved.
UNIT 1: compiled on Jan 21 2024 at 08:24:28 labeled as SPS08095n
(31457280 bytes) from Primary SPS08095n.bin (UFI)
SW: Version 08.0.95nT211
Compressed Primary Boot Code size = 786944, Version:10.1.26T225 (mnz10126)
Compiled on Tue Nov 29 12:43:26 2022

HW: Stackable ICX7150-C12-POE
==========================================================================
UNIT 1: SL 1: ICX7150-C12-2X1G POE 12-port Management Module
Serial #:FEK3817Q8F6
Software Package: BASE_SOFT_PACKAGE
Current License: 2X1G
P-ASIC 0: type B160, rev 11 Chip BCM56160_B0
==========================================================================
UNIT 1: SL 2: ICX7150-2X1GC 2-port 2G Module
==========================================================================
UNIT 1: SL 3: ICX7150-2X10GF 2-port 20G Module
==========================================================================
1000 MHz ARM processor ARMv7 88 MHz bus
8 MB boot flash memory
2 GB code flash memory
1 GB DRAM
STACKID 1 system uptime is 10 minute(s) 7 second(s)
The system started at 10:02:35 GMT+00 Fri Jun 07 2024

The system : started=warm start reloaded=by "reload"

SSH@ICX7150-C12 Switch#show flash
Stack unit 1:
NAND Type: Micron NAND 2GiB (x 1)
Compressed Pri Code size = 31457280, Version:08.0.95nT211 (SPS08095n.bin)
Compressed Sec Code size = 31457280, Version:08.0.95nT211 (SPS08095n.bin)
Compressed Pri Boot Code size = 786944, Version:10.1.26T225 (mnz10126)
Compressed Sec Boot Code size = 786944, Version:10.1.26T225 (mnz10126)
Code Flash Free Space = 1113423872