cancel
Showing results for 
Search instead for 
Did you mean: 

ICX-7510 Switch Disconnected - Lennar Homes

Rathda
New Contributor

Help! Noticed web pages were slow at loading and realized after weeks my switch is shown as disconnected through the unleashed app and website. Unsure of how to get this reconnected. I’m not IT savvy but tech savvy; a dumbed down response would be greatly appreciated!

5 REPLIES 5

BenBeck
Moderator
Moderator

*moved to Lennar forum

 

Ben Beck, RCNA, RCNI, Principal Technical Support Engineer
support.ruckuswireless.com/contact-us

Vásquez_Fer
Moderator
Moderator

/Hi @Rathda 

Hope you are doing well! 

If there was a blackout or power outage and the switch reboot because of that, most possible your switch starts running the wrong code which we call ‘routing code’ this is a know issue.

 

Vsquez_Fer_0-1669725500238.png

 

An identifier of this problem is that it comes out as Switch-Router in the unleashed dashboard.

There we are going to see 2 important things the

MAC address: Physical address of the device this never changes

The IP address is a logical address assigned by your local router (ISP) to the device (this can change and may not be the same as the one shown on the dashboard)

1- To fix this issue, we must identify the IP address of the switch 'currently'

-We can try the IP address that shows in the dashboard copy and paste it in the URL if that redirects you to the login page for the ICX-7150-C12P that is the correct one if not.

I will leave you a guide how to perform an IP scanner on your local network to identify the switch IP address very easily. 

How to find my Ruckus “Devices IP address” using free applications

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-find-my-Ruckus-Device...

2-Once we identified the IP address of the switch proceed to access remote to the device 'command Line' 

How to remotely access to 'ICX 7150-12P' or 'access points' "Network devices"

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-remotely-access-to-IC...

If you can access to the Command line should look like this:

ICX7150-C12 Router>

3-Here is a quick guide to understand how to fix the 'routing code issue' but basically you need only need to run the following commands once you are on the command line 'CLI' 

Note: Hit Enter to accept each command

enable

copy flash flash secondary 

boot system flash secondary yes 

example: 

ICX7150-24P Router>enable (hit enter to accept the command)
ICX7150-24P Router#copy flash flash secondary (hit enter to accept the command and wait: until the flash finished )
ICX7150-24P Router#boot system flash secondary yes ( hit enter to accept the command  : the switch will reboot )

How to Fix Routing code issues on Lennar Home users

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Fix-Routing-code-issu...

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-solve-the-routing-cod...

4-If the access via IP address is not possible here is a guide how to access to the Switch via console (cable access between your PC to the ICX 7150-C12P) in this case we need a USB type C to USB standard or Console cable Rj45 to USB. 

How to console in the ICX-7150-C12P

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-console-in-the-ICX-71...

Once you are log in the ICX-7150-C12P please follow up the same steps that are on point '3'

Best Regards 

Fernando Vasquez 

I've downloaded Putty and MobaXterm and I'm able to get to the point where it's asking me for login username but when I enter all of the suggested options for SSH or Telnet it asks for a password and then it's like my keyboard is disabled and I can't enter any command in that field.

Finnejo
New Contributor II

Does anyone ever respond here?