cancel
Showing results for 
Search instead for 
Did you mean: 

ICX 7150-C12P switch random reboots

Therealx24
New Contributor

My ICX 7150-C12P switch is currently up but is randomly rebooting itself. I have a single R510 AP connected to the switch. This started happening several days ago; the switch reboots about every 10-20 minutes, stays up for a while, then starts rebooting itself again randomly. The AP has been updated to the latest 200.14 firmware.

I verified my internet connection is functioning normally (had Spectrum tech out to check yesterday).

How do I go about resolving this issue?

1 ACCEPTED SOLUTION

Hi @Therealx24 

Thank you for the response and the update.

We suggest upgrading your switch to the latest stable version as your Switch is on an older version that is 08080d. (as highlighted in the below screenshot)

Please follow to the below steps explaining the Upgrade process. 

The recommended stable versions is 8095g (08.0.95g)

The Upgrade path would be: 08080d (your current version)>>8080f>>8095g

(PLEASE NOTE: Use 08095g patch in place of 8095h as explained in the guide)

Your Upgrade folder should contain these 3 files shown in the below screenshot: (Refer the guide link for more information)

Below are the options or methods to perform the Upgrade on the switch: You could choose any one of these.

1st Option:

1. In this option, we will use a pen drive or USB flash drive in which we move the files to the pen drive and connect it to the Switch then through CLI we execute the commands to upgrade the Switch using the following guide as a reference:

How to Upgrade a Switch ICX-7150-C12P using a USB flash drive

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

2nd Option:

2. The following guide is an example of an upgrade via TFTP server, by using an application (FREE) to send files or upload remote files to a device, in our case, we will use it to update a new version to the Switch, basically it will send the image version remotely from the computer to the switch.

How to upgrade a Switch ICX7150-C12P via TFTP

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-Upgrade-a-Switch-ICX-...

3rd Option:

3. In this option we Upgrade the Switch from the Web Interface (GUI) of switch.

https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/How-to-perform-an-Upgrade-vi...

Try to access your switch from a web browser by pasting the below URL in http or https form whichever that works.

https://0.0.0.0 or http://0.0.0.0 (IP address of Switch. 0.0.0.0 is just as an example)

As you can access CLI, I would suggest you follow the 2nd option. 

Please let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

 

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

View solution in original post

31 REPLIES 31

Error after copy flash flash secondary:

.................................The calculated data payload crc 0xc322dac7 and the crc for the payload 0xbc1580ff mismatch

Invalid Image. No write to flash...
Copy Failed.
telnet@ICX7150-C12 Router#

Hi @Therealx24 

Greetings!!!

Thank you for the response and the information you shared.

Please enter below commands and try.

enable

reload  (This command will reboot the Switch)

(Wait until the Switch comes up after reboot and restart Putty, perform next commands) 

copy flash flash secondary 

boot system flash secondary yes 

Please check and let me know if you have any queries in this regard.

Thank you again for your patience.

 

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Rebooted, re-entered copy flash flash secondary, but received the following error:

..................................The calculated data payload crc 0xb8d47123 and the crc for the payload 0xbc1580ff mismatch

Invalid Image. No write to flash...
Copy Failed.
telnet@ICX7150-C12 Router#

Hi @Therealx24 

Please enter below commands:

enable

boot system flash primary yes 

Please let me know once it gets completed.

Thank you again for your patience and understanding.

 

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.

Okay, ran enable boot system flash primary yes. Switch has rebooted now. What next?