ICX-7150-C12P Part 2

[WaveWarden]

I posted a few months ago that my Lennar smart home things, like my ring doorbell, have gone down, because my access points are no longer providing access. I submitted photos of the ruckus and the access points and was told to log into the access point and make sure all the ports were turned on. By the time I was able to find the IP address and see that they were already on, my ticket was closed.  The original post was from ‎06-06-2025 08:57 PM. Please see that post for what we’ve done. 

[Imran_ruckus]

Hi @WaveWarden 

Greetings!!!

Thank you for reaching out to the RUCKUS Lennar Home Community. 

We appreciate your patience and understanding as we work to resolve the issues you are experiencing with your RUCKUS setup.

Based on the information provided, it appears that you are encountering intermittent internet connectivity. 

We apologize for any inconvenience this has caused and are committed to assisting you promptly.

Based on your previous post steps, we may need to check some configurations of your RUCKUS ICX-7150-C12P Switch to troubleshoot this issue.

To proceed with troubleshooting the issue, please follow the steps outlined below to access the Command Line Interface (CLI) and provide the necessary command outputs:

1. First, identify the current IP address assigned to the switch ICX-7150-C12P by your local router. You can use an IP scanner tool to easily locate the switch's IP address on your network. Here is a guide on how to perform this using the IP Scanner free application: 

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-find-the-IP-Address-o...

2. Once you have identified the IP address of the switch, proceed to access the Command Line Interface (CLI) of the RUCKUS ICX-7150-C12P switch. Here is a guide on how to access the CLI: 

https://community.ruckuswireless.com/t5/RUCKUS-Lennar-Support-Knowledge/How-to-access-the-Command-Li...

If you can access the Command line, the prompt should look like below:

ICX7150-C12 Router> OR

ICX7150-C12 Switch>

3. After successfully accessing the CLI, please execute the following commands and provide the outputs:

   enable

   show version

   show flash

   show inline power

   show inline power detail

   show interface brief

Please share the command outputs or screenshots if you encounter any issues or errors during these steps. 

Feel free to reach out if you have any questions or require further assistance.

Thank you for your cooperation and patience.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support

[WaveWarden]

 

  

[Imran_ruckus]

Hi  @WaveWarden 

Greetings of the day!!!

Thank you for sharing the requested information.

Based on the troubleshooting done, your ICX-7150-C12P Switch has old firmware and seems it be corrupted causing issues.

As a result, this Switch unit appears to be defective and needs to be replaced through the RMA (Return Merchandise Authorization) process.

To initiate the replacement, please contact us via chat using the link provided below in this post. Kindly copy the URL/link of this post and paste it in the chat along with the serial number of your RUCKUS Switch when prompted.

Please refer to the example screenshot below for guidance on how to copy and share the required information:

The below link is to contact us by chat (only)

https://support.ruckuswireless.com/contact-us

Did I answer your queries? If yes, hit the Kudos buttons and also accept the answers as Accepted solutions.

Please let me know if you have any queries in this regard.

Thank you again for your patience and understanding.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support

[Imran_ruckus]

Hi @WaveWarden 

Greetings!!!

I trust this message finds you well.

I kindly request an update on the status of the issue so that we may proceed further with resolving it.

Thank you.

Best regards,
Imran Sanadi
RUCKUS | Lennar Home Community Support