Creating vlans on 7150-C12P and R510.

[PastorLopez]

Hello all,

I've been trying to set up new SSIDs with different VLANs but so far haven't had any luck.

My current set up is the following:

Router: Edger Router X

Switch: ICX7150-C12

AP: R510

I have created the VLANs (11, 111,112) on my router with its DHCP pools. My router goes to port 1/1/5 on my switch and my two APs go to 1/1/4 and 1/1/6.

This is the setup on the switch...

vlan 1 name DEFAULT-VLAN by port
!
vlan 11 name Guest by port
tagged ethe 1/1/1 to 1/1/2 ethe 1/1/4 ethe 1/1/6
spanning-tree 802-1w
!
vlan 111 name IoT by port
tagged ethe 1/1/1 to 1/1/2 ethe 1/1/4 to 1/1/6
spanning-tree 802-1w
!
vlan 112 name Management by port
tagged ethe 1/1/1 to 1/1/2 ethe 1/1/4 to 1/1/6
spanning-tree 802-1w

Config for port 1/1/5...

sh int ethe1/1/5
GigabitEthernet1/1/5 is up, line protocol is up
Port up for 18 day(s) 14 hour(s) 30 minute(s) 20 second(s)
Hardware is GigabitEthernet, address is c0c5.20a9.59ed (bia c0c5.20a9.59ed)
Configured speed auto, actual 1Gbit, configured duplex fdx, actual fdx
Configured mdi mode AUTO, actual MDIX
PTP Feature Disabled
Tagged member of 2 L2 VLANs, untagged in VLAN 1, port state is FORWARDING
BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled
Link Error Dampening is Disabled
STP configured to ON, priority is level0, mac-learning is enabled
MACsec is Disabled
Flow Control is config enabled, oper enabled, negotiation disabled
Mirror disabled, Monitor disabled
Mac-notification is disabled
VLAN-Mapping is disabled
Not member of any active trunks
Not member of any configured trunks
No port name
IPG MII 96 bits-time, IPG GMII 96 bits-time
MTU 1500 bytes
MMU Mode is Store-and-forward
300 second input rate: 4629176 bits/sec, 399 packets/sec, 0.46% utilization
300 second output rate: 42584 bits/sec, 41 packets/sec, 0.00% utilization
559192391 packets input, 762511322962 bytes, 0 no buffer
Received 130654 broadcasts, 1482 multicasts, 559060255 unicasts
0 input errors, 0 CRC, 0 frame, 1 ignored
0 runts, 0 giants
142245845 packets output, 56443883456 bytes, 0 underruns
Transmitted 1293835 broadcasts, 3948425 multicasts, 137003585 unicasts
0 output errors, 0 collisions
Relay Agent Information option: Disabled
Protected: No
MAC Port Security: Disabled

This port is not being monitored for queue drops
Egress queues:
Queue counters Queued packets Dropped Packets
0 135789381 0
1 0 0
2 1631 0
3 0 0
4 3202377 0
5 298307 0
6 0 0
7 2954149 0

On the Ruckus management console, I have already created the SSIDs using its corresponding VLAN.

I'm confuse on how the tag/untag process works with Rukus. Any help on pointing me in the right direction will be appreciated.