Can't upgrade ICX 7150 to image 8095g - The code type 64 is not correct for the target hardware

[Rjndael]

PoE has recently went offline on my Ruckus 7150 switch. When I connect to the console I see the following error messages:
> Vmain (48V) fault has forced all ports on slot 0 to lose power.

I've attempted to upgrade the image to version 8095g over TFTP as advised in https://community.ruckuswireless.com/t5/RUCKUS-Support-for-Lennar-Homes/POE-Fatal-message-is-floodin...

When I enter the upgrade command, I get the following error:
--------------

copy tftp flash 192.168.0.9 SPS08095gufi.bin bootrom
telnet@ruckus-switch#The code type 64 is not correct for the target hardware, abort!
File Type Check Failed

--------------

Version:
--------------

telnet@ruckus-switch#show version
Copyright (c) 1996-2017 Brocade Communications Systems, Inc. All rights reserved.
UNIT 1: compiled on Aug 14 2017 at 06:54:44 labeled as SPS08061a
(24723488 bytes) from Primary SPS08061a.bin
SW: Version 08.0.61aT211
Compressed Boot-Monitor Image size = 786944, Version:10.1.10T225 (mnz10110)
Compiled on Sun Jun 25 09:25:15 2017

HW: Stackable ICX7150-C12-POE

-------------

Tried upgrading to 08070c and 08070aa, similar message, but the code is 33 instead.

Tried upgrading to 08080f first, as advised in the link. Tried all 4 images, received the following errors:

-------

telnet@ruckus-switch#copy tftp flash 192.168.0.9 SPS08080f.bin bootrom
telnet@ruckus-switch#The code type 33 is not correct for the target hardware, ab ort!
File Type Check Failed

TFTP to Flash Error - code 8
telnet@ruckus-switch#copy tftp flash 192.168.0.9 SPS08080fufi.bin bootrom
telnet@ruckus-switch#The code type 64 is not correct for the target hardware, ab ort!
File Type Check Failed

TFTP to Flash Error - code 8
telnet@ruckus-switch#copy tftp flash 192.168.0.9 SPR08080fufi.bin bootrom
telnet@ruckus-switch#The code type 64 is not correct for the target hardware, ab ort!
File Type Check Failed

TFTP to Flash Error - code 8
telnet@ruckus-switch#copy tftp flash 192.168.0.9 SPR08080f.bin bootrom
telnet@ruckus-switch#The code type 33 is not correct for the target hardware, ab ort!
File Type Check Failed

TFTP to Flash Error - code 8

------

Please advise.

[Isai_Roa]

Hi.

How to you used rftp?

In the Switch they show me that command isn't possible

SW_RUCKUS_DATACENTER#copy rftp flash
Invalid input -> rftp flash
Type ? for a list

[Imran_ruckus]

Hi @Isai_Roa 

Greetings!!!

Thank you for contacting RUCKUS Lennar Home Community.

Hope you are doing well

Please note it is tftp and not rftp

As this case is raised by @Rjndael 

If you are a Lennar Home RUCKUS device user, to avoid confusion with posts please raise your own post/case on 'RUCKUS Lennar Support',  and a detailed description of the network issue and what you've done so that we can guide you properly.

Thank you again for understanding.

Best regards,

Imran Sanadi

RUCKUS Lennar Home Community.